Summers DK9630 Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 82

background image

SPLICE&GANGTUBE INSTALL

7/25/2018

9K2827.iam/

A

1.  INSTALL 8K1075 SPLICE TUBE WITH HARDWARE AS SHOWN, AND TIGHTEN.

2. INSTALL 8K1560 GANG HOUSING WITH 8K1660 PIN. RETAIN WITH 8X0044
     BOLT AND 8X0234 NUT.

3.  INSTALL 8K6313 CYLINDER AS SHOWN WITH 8X0138 BOLT AT BASE END OF
   CYLINDER, AND 8X0146 BOLT AT ROD END.  INSTALL 8X0281 NUTS AND TIGHTEN.

DO NOT OVERTIGHTEN.

CYLINDER MUST BE FREE TO ROTATE.

4. ATTACH 8K1575 GANG MOUNT TUBE IN LEFT LOCATION USING 8K1760 BOLT AND 8X0288

NUT. DO NOT OVERTIGHTEN, AS THE GANG TUBE MUST BE FREE TO ROTATE, BUT STILL SNUG.

5. ATTACH SECOND 8K1575 GANG MOUNT TUBE, IN THE SAME MANNER, IN RIGHT LOCATION TO

8K1570 AS SHOWN.

6. ATTACH 8K1570 TO 8K1560 AS SHOWN.

8K1575

8K1660

8X0234

7/16" LNUT

8X0281

NY-LOCK 1"

8X0067

1/2-13NCX2-1/4"

8X0242

NY-LOCK 1/2" N

8K1770

8X0405

8K1585

7K3218

8X0146

1 X 8-1/2"

8X0285A

1-1/2" NYLOCK

8X0352

8K1775

8X0288

8K1760

8X0114

3/4 x 3"

8X0317

3/4" FW

8X0306

3/4" LW

8X0260

3/4" N

8X0138

1 X 5-1/2"

8X0281

NY-LOCK 1"

8X0281

NY-LOCK 1"

8X0261

3/4" LN

8Z0475

8K1075

8X0044

7/16" X 3-1/2"

8K6313

8K1570

8K1555

8K1582

8X0114

3/4 x 3"

8X0044

7/16" X 3-1/2"

8X0234

7/16" LNUT

7. ATTACH HOUSING TO 8K1075 SPLICE TUBE WITH 8K1660 PIN AS SHOWN. NEXT CONNECT ROD END OF 8K6313 CYLINDER TO HOUSING AS

SHOWN.

8. INSERT 8K1775 SLIDE SHAFT INTO HOUSING AND RETAIN WITH 8X0352 WASHERS AND 8X0285A NYLOCK NUTS (FROM EACH SIDE). **DO NOT

TIGHTEN NUTS.

9. THREAD 8K1770 ADJUSTMENT SCREW INTO 8K1775 SLIDE SHAFT UNTIL THERE IS APPROXIMATELY 16" FROM THE REAR END OF ADJUSTMENT

SCREW TO THE SLIDE SHAFT.

10. ATTACH 8K1580 REAR CAP WITH 8X1115 CARRIAGE BOLTS AND 8X0203 FLANGE NUTS, PASSING 8K1770 ADJUSTMENT SCREW THROUGH

HOLE IN CAP AS SHOWN.

11. TIGHTEN NUTS ON BOTH ENDS OF SLIDE SHAFT, TAKING CARE TO ENSURE THE SLIDE SHAFT IS CENTERED IN THE HOUSING.

12. INSTALL 8K1555 LINK BARS TO SLIDE SHAFT AND GANG MOUNT TUBES. INSTALL 8K1582 ANGLE GAUGE OVER THE TOP OF HOUSING AS

SHOWN AND SECURE USING 8X0114 BOLTS AND 8X0261 NYLOCK NUTS.

13. ATTACH 8K1585 CRANK HANDLE TO ADJUSTMENT SCREW WITH 8X0067 BOLT AND 8X0242 NUT. 8X0405 PIN IS PROVIDED TO RETAIN THE

HANDLE AND PREVENT UNWANTED MOVEMENT OF THE ADJUSTMENT SCREW.

14. ROTATE HANDLE TO ENSURE THE GANG MOUNT TUBES PIVOT

FREELY, AND WITHOUT EXCESSIVE INPUT FORCE ON THE HANDLE.

SECTION 4 - PARTS

4-12

«
...
56
57
58
59
60
...
»

Содержание DK9630



















































































Отзывы:

Нет отзывов

Похожие инструкции для DK9630

Бренд: AAON Страницы: 36

Бренд: Fisher Scientific Страницы: 42

Бренд: Facnor Страницы: 33

Бренд: CAE Healthcare Страницы: 108

Бренд: Cannon Страницы: 36

Бренд: Parker Страницы: 39

Бренд: Hagerman Страницы: 4

Бренд: hager Страницы: 2

TECSHOW QUAD SPIDER 60

Бренд: Ampro Страницы: 9

TRAKTOR KONTROL S4

Бренд: Native Instruments Страницы: 86

Бренд: Native Instruments Страницы: 245

Бренд: Sagola Страницы: 62

Бренд: Ultraflex Страницы: 52

Бренд: Palmgren Страницы: 12

Бренд: Bartscher Страницы: 20

Бренд: Kaiweets Страницы: 6

Бренд: Kaiweets Страницы: 6

Ti-Max NLX nano

Бренд: NSK Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды