Summers DK9630 Скачать руководство пользователя страница 44

Страница: 44 / 82

SECTION 3 - OPERATION & MAINTENANCE

TRANSPORTING

The Summers Diamond Disk & DT9530 are equipped with

manual wing and center lift cylinder locks. The following

procedure should be used to prepare disk for transport.

1. Check that wing locks are in the storage positions.

2. Fully extend main lift cylinders, quickly lower disk ap-

proximately 1”, raise wings.

3. Install safety locks on wings and center lift cylinders.

4. USE a safety chain between tractor drawbar and disk

hitch when transporting on public roads.

Check wheel bolts / nuts after first 20 miles of road

transport and every 60 miles there after.

Road the implement at a reasonable speed not to exceed

20 miles per hour.

Always use an ASAE “Slow Moving Vehicle” emblem and

Safety Lights when transporting on a road or highway.

Comply with your state and local laws governing lighting

and maximum width regula

tions. Transport during daylight

hours only.

STORAGE

Proper rust prevention treatment of equipment before placing in

storage will not only lengthen its useful life, but will assist in main-

taining optimum performance when put back into service.

The following list contains suggestions for preparing your imple-

ment for storage.

1. Clean entire machine. Remove all dirt and excessive grease

implement.

2. Check disk over thoroughly for damaged or worn parts,

cracked or broken blades, and loose bolts.

3. Wheel bearings should be cleaned and repacked each year.

4. Grease all zerks on implement.

5. Block up to remove weight from tires.

6. If implement is lowered to the ground, place boards under

blades.

7. Disconnect rods and fully retract the cylinders to prevent rust-

ing of shafts and subsequent seal damage. If left extended,

coat rods with grease to prevent corrosion. Remove grease

prior to retracting cylinders.

8. For safety, do not store implement with wings folded up.

9. Clean and place a protective coating of heavy oil or grease

on earth-working parts to prevent rusting.

10. Touch-up any spots where paint has been scratched or

worn off.

3-4

Содержание DK9630



















































































Результаты поиска

Содержание DK9630

Отзывы:

Похожие инструкции для DK9630

Бренды по названию

Популярные бренды

Summers DK9630, Руководство оператора

Результаты поиска

Содержание DK9630

Отзывы:

Похожие инструкции для DK9630

Бренды по названию

Популярные бренды