background image

Safety Section 

 

 
 
 
 
 
 
 
 
 
 
 

 

Refer to OSHA 1910.132 

(Personal Prot. Equip.)

 

To avoid electric shock or electrocution, all 
equipment must be properly wired and grounded 
according to electrical codes. Have unit wired by 
qualified electrician. 

 
Have an electrician install a main power disconnect 
switch capable of being locked only in OFF position. 
Mark disconnect 
clearly as to 
equipment it 
operates. 
Always lock out 
main power 
disconnect 
switch whenever 
equipment is not 
in use. 

 

 

WARNING: When servicing equipment, never 
enter bin unless all power is locked out and 
another person is present. Always LOCK OUT 

all power and always check with voltage meter before 
servicing. 
 
Failure to do so could result in death or serious injury. 
 
Owners/operators are responsible for developing 
site-specific Lockout/Tagout procedures based on 
equipment at their work site. See 

OSHA’s typical 

minimal lockout procedures (29CFR 1910.147 App A) 
at www.osha.gov. 

 

 

WARNING: KEEP CLEAR OF ALL MOVING 
PARTS

Keep people (ESPECIALLY YOUTH) away from 
equipment, particularly during operation. 
 
Keep away from all moving parts. 
Keep all shields in place. SHUT 
OFF AND LOCK OUT
 all power 
before servicing. 
 
Failure to follow precautions above 
could result in death or serious 
injury. 
 

WARNING:  Metal is slippery when wet. To 
avoid falls, never carry items if climbing on 

bin. Maintain secure hand and foothold if climbing on 
bin. Failure to do so could result in death or serious 
injury. 

 

 

CAUTION: Metal edges are sharp. To avoid 
injury, wear protective clothing and handle 
equipment and parts with care. 

 
Failure to do so may result in minor or moderate injury. 

 

 

PERSONAL PROTECTIVE EQUIPMENT 

Owners/Operators are 
responsible for developing 
site-specific personal 
protective equipment 
standards. OSHA’s 
personal protective 
equipment standards 
(29CFR 1910.132) can be 
found at www.osha.gov. 

 
 
 
 
 
 

EMERGENCIES – KNOW WHAT TO DO 

Have emergency numbers and written directions to 
work site readily available in case of emergency. An 
area for emergency phone numbers to be recorded is 
provided below and at end of this manual. 
 

Ambulance • Fire • Police: 9-1-1 

Bin rescue team: _______________________

 

Emergency medical squad: ______________ 

Address of work site: ___________________ 

Directions to work site:__________________

 

 

Содержание Spredway

















Отзывы: