1.1 g
enerAl
notes
on
sAfety
This operation manual is applicable for the machine UBK
6-R. The machine may only be handled by personnel who
are qualified.
Hold power tools by insulated gripping surfaces when
performing an operation where the cutting tool may con-
tact hidden wiring or its own cord. Contact with a «live»
wire will make exposed metal parts of the tool «live» and
shock the operator.
WARNING Read all safety warnings and all in-
structions.
Failure to follow the warnings and in-
structions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
1.2 u
se
of
the
mAchine
for
PurPoses
for
which
it
is
intended
The machine is designed for grinding and polishing of
metal, plastic or wood with abrasive belts, non-woven
belts, high-performance ceramic belts or reinforced non-
woven belts, without using water. The machine is de-
signed exclusively for a 2-hand application.
1.3 i
ncorrect
use
All uses other than those described under section
1.2 are regarded as incorrect use and are there-
fore not admissible.
1.4 ec
declArAtion
of
conformity
Otto Suhner GmbH of Trottäcker 50, D-79713 Bad Säck-
ingen, hereby declares under sole responsibility that the
product with the serial or batch no. (see reverse side) com-
plies with the requirements under the Directive 2014/30/
EU, 2006/42/EC, 2011/65/EU. Applied standards: EN ISO
12100, EN 60745, EN 55014-1, EN 55014-2, EN 61000-3-
2, EN 61000-3-3. Document Agent: M. Voyame. D-Bad
Säckingen, 10/2018.
M. Voyame/Division manager
2.1 P
rior
to
tAKing
the
mAchine
into
serVice
Before connecting tool to a power
source, be sure the voltage sup-
plied is the same as specified on
the name plate of the tool.
Check the grinding belt before use. The driver roller must
be installed centrally and aligned to the stop. Under no
circumstances must the grinding belt exceed the max
permitted speed. Observe national regulations. Take pro-
1. n
oteS
on
S
afety
2. c
ommISSIonIng
tective measures when dust can develop during working
that is harmful to one’s health, cumbustible or explosive.
Wear a dust mask and work with dust/chip extraction
when connectable. Remove safety guard.
Do not use accessories which are not spe-
cifically designed and recommended by the
tool manufacturer.
Just because the accessory
can be attached to your power tool, it does not assure safe
operation.
2.2 t
AKing
the
mAchine
into
serVice
Select a speed from the table and set this for the grinding
belt at the setting wheel.
Level 1: 14.7m/s
Level 4: 23.6m/s
Level 2: 17.3m/s
Level 5: 26.8m/s
Level 3: 20.5m/s
Level 6: 31m/s
Never raise the speed chosen for the belt when it
is running!
2.2.1 t
unr
on
/t
urn
off
The switch must be in the OFF position. To turn the ma-
chine on, push the ON/OFF switch toward the front unteil
it clicks in. Press the ON/OFF swith to trigger the blocking
and the machine shuts down.
2.3 r
Ating
dAtA
Power voltage
230/240V/120V, 50/60Hz
Power Input 230/240V // 120V
1530W // 1340W
Power Output 230/240V // 120V
1000W // 800W
Belt speed in idle
14.7-31m/s
Lenght of the grinding belt
450mm
Width of the grinding belt
35mm
Grinding belt type
Nonwoven and grinding belts
22
CN
PL
CZ
FI
SE
NL
PT
ES
IT
EN
FR
DE
EN
Содержание UBK 6-R
