SUHNER ABRASIVE ROTOmax 4.0, Техническая документация

Страница: 33 / 92

2.3 r
Ating dAtA
Voltage 3~400-480V, 50-60Hz, 9.5-7.9A
Power Input 4000W
Power Output 3500W
Protection class 1
Type of protection IP45
Overload protection yes
No-load speed 500-10000min
-1
Sound pressure level 75dB(A), K=1.5m/s
2
Threaded connection for flexible shafts of type:
DIN 15 M14
NA 10, NA 12, NA 15
see catalog
NA 12 DIN 15/G28 STEP see catalog
NA 15 DIN 15/G35 STEP see catalog
2.3.2 V
iBrAtion mesurement VAlues of hAnd tools
FH 15 Measurement value 3.1m/s
2
/K=1.5m/s
2
Drive 10000min
-1
SAM 1:1 Measurement value 6.6m/s
2
/K=1.5m/s
2
Drive 6400min
-1
BSG 10 Measurement value <2.5m/s
2
/K=1.5m/s
2
Drive 7000min
-1
FSM 1:1 Measurement value 4.7m/s
2
/K=1.5m/s
2
Drive 7000min
-1
WI 10 Measurement value 3.5m/s
2
/K=1.5m/s
2
Drive 15000min
-1
WH 15 Measurement value <2.5m/s
2
/K=1.5m/s
2
Drive 5000min
-1
WH 12 Measurement value <2.5m/s
2
/K=1.5m/s
2
Drive 10000min
-1
FH 12 Measurement value 7.1m/s
2
/K=1.5m/s
2
Drive 12000min
-1
BSG 15 Measurement value <2.5m/s
2
/K=1.5m/s
2
Drive 5000min
-1
According to ISO/EN 60745.
The specified vibration value was measured with a
standardised test method and may differ from the
actual operating value. The specified value can be
used for product comparisons or for an introductory as-
sessment of work breaks.
2.4 o
perAting conditions
Temperature range during operation: 0 to +50°C
Relative air humidity: 90% at +30°C, 65% at +50°C
To avoid strong looping movements and beaming
of the flexible shafts, the working pressure must
be reduced.
3.1 m
Achine
3.1.1 c
ontrol KeypAd
Speed gauge (1). Speed correction «-/+» (2). Speed con-
firmation «enter» (3). «run» start command (4). «stop» stop
command (5). ON/OFF «step» safety device (6).
3.1.2 s
tArting the mAchine
Before turning on the machine, make sure to re-
move wrenches and adjusting tools.
When turning on, hold the flexible shaft extended.
During operation make sure that the flexible shafts have
large bend radius.
Before starting the machine, hold the hand tool against
turning!
Operate power switch of the machine.
Speed gauge blinking.
Pre-select speed with key «-/+».
The speed gauge blinks until the pre-selection is con-
firmed with the «enter» key.
The speed is saved.
If a start command is not issued within 60 seconds, the
speed gauge will start to blink.
Now pre-select the speed again by pressing the «enter»
key.
Press the «run» key = Start the machine.
During operation the speed can be varied with the «-/+»
keys.
3.1.3 m
Achine stop
Press «stop» key.
Hold hand tool steady until the speed Zero is reached.
Speed blinks.
3. h
andlIng
/o
PeratIon
PT
ES
IT
EN
FR
DE
NL
PL
CZ
FI
SE
CN
EN
33