SUG AWI Series Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 12

SUG AWI Series Скачать руководство пользователя страница 12

19. Do not use the additional tools to extend the length of the handle, such as: iron or

plastic pipe.

20. Do not touch any button when torque is exerted.

21. The digital torque wrench cannot be applied to the conductive tools.

LUBRICATE

The wrench’s internal mechanism is permanently lubricated during assembly.

Do not

attempt to lubricate the internal mechanism.

ACCESSORIES

Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool may become hazardous when used on

another tool.
Recommended accessories for use with your tool are available at extra cost from your

local service center.

IMPORTANT:

To assure product SAFETY and RELIABILITY, repairs, maintenance

and adjustments should be performed by certified service centers or other qualified

service organizations, always using identical replacement parts.

PROTECTING THE ENVIRONMENT

Before disposing of damaged, check with your state Environmental Protection Agency

to find out about special restrictions on the disposal of tool or return them to a certified

service center for recycling.

«
...
10
11
12

Содержание AWI Series













Отзывы:

Нет отзывов