Consult the MSDS that accompanies each standards set to identify proper
disposal techniques.
If you experience an issue with the printed circuit assembly (PCA) that
contains a lithium battery, please contact SUEZ for return instructions.
Whenever changing the lithium battery, observe the correct polarity. Dispose
of used batteries according to the manufacturer’s instructions and local
disposal requirements.
To protect the Analyzer from damage, always drain the water from the
Analyzer prior to shipping.
Warnings
(continued from page 1)
This symbol
on the instrument indicates that the user should refer to
the manual for operating instructions.
The vial sparging assembly contains sharp needles designed to pierce
the septa of sample vials. Do not put fingers or inappropriate materials
into the vial sparging assembly.
For continued protection against fire hazard, replace fuse with same
type and rating.
This symbol indicates the protective earth terminal (ground) for the
Analyzer.
This symbol indicates that to comply with European Union Directive
2002/96/EC for waste electrical and electronic equipment (WEEE),
the Analyzer should be disposed of separately from standard waste.
This symbol on the instrument indicates that the user should refer to
the manual for instructions on filling the DI water cartridge, as found
in the Installation and Maintenance chapters.
To protect against accidental exposure to ultra-violet radiation, do not operate
the UV lamp outside of its protective housing.
This is a Safety Class I product. It must be must be attached to a grounded
power source.
If this instrument is used in a manner not specified by SUEZ, the protection
provided by the instrument may be impaired.
Always stop analysis before turning off or unplugging the Analyzer.
Make sure the DI water cartridge is full, particularly when running samples
with high TOC or high salt concentrations. Always “clean-up” the Analyzer by
running low-TOC DI water after running high TOC or salt samples.
This is a Class A product. In a domestic environment, this product may cause
electromagnetic interference in which case the user may be required to take
adequate measures to correct the interference.
To avoid false TOC readings and possible damage to the Analyzer, always
make sure the sample inlet is open and the DI water cartridge is filled before
starting analysis.
The glass window in the UV reactor indicates proper lamp operation and
should not be viewed too closely (closer than 6 inches) or for extended
periods (greater than 1 minute). Protective eyewear is recommended.
This symbol on the Sievers 860 TOC Analyzer indicates that the
product does contain restricted substances included in China RoHS II.
Please refer to the following table.
5
6060 Spine Road
Boulder, CO 80301-3687 USA
total organic carbon
1
Linear Range
Precision
Accuracy
Analysis Time
Sample Flow Rate (nominal)
Sample pH
0.3 ppb – 1.5 ppm TOC
0.1 ppb or 1%, whichever is greater
± 5% at 500 ppb sucrose standard
6 minutes
Analysis mode: 0.25 mL/min
Fast Flush (between samples): 0.5 mL/min
<3
analyzer specifications
Power Requirements
Fuses
Ambient Temperature
Normal Operating Environment
Maximum Relative Humidity
Maximum Altitude
Sparge Gas Inlet Pressure
Sparge Gas Flow Rate
Calibration Stability
Outputs
Installation/Overvoltage Category
Safety Certifications
Pollution Degree
Display
Size
Weight
100–240 ±10% VAC, 60 watts, 50/60 Hz
T1.6 A, 250 VAC (SloBlo), size 5 x 20 mm (appliance inlet)
10 °C to 40 °C
Intended for indoor use only
Up to 95%, non-condensing
3,000 m (9,843 ft)
30 psig to 50 psig
120 mL/min to 150 mL/min
Typically stable for 12 months
USB, Ethernet port
II
CE, ETL listed. Conforms to UL Std. 61010-1.
Certified to CSA C22.2 No. 61010-1
2
Color LCD
H: 43.0 cm (16.9 in); W: 21.5 cm (8.5 in); D: 42.0 cm (16.5 in)
10.5 kg (23.0 lb)
Sievers Autosampler RT12 specifications
Capacity
Power Supply
Ambient Temperature
Normal Operating Environment
Maximum Relative Humidity
Maximum Altitude
Size
Net Weight
Safety Certification
Twelve (12) 40-mL vials
Power supplied by the Sievers 860 Laboratory TOC Analyzer
10 °C to 40 °C
Intended for indoor use only
Up to 95%, non-condensing
3,000 m (9,843 ft)
H: 36.8 cm (14.5 in); W: 23.1 cm (9.1 in); D: 25.4 cm (10.0 in)
3.9 kg (8.6 lb), including the empty sample rack
CE
1
Stated analytical performance is achievable under controlled laboratory conditions that minimize operator and standards errors.
DQS 79000-03 EN Rev. A
