SubSurface Instruments PL-VF Series Скачать руководство пользователя

Страница: 4 / 28

www.ssilocators.com

SERIES

Congratulations on the purchase of your new SubSurface Instruments, Inc. PL-VF Series Cable, Pipe & Fault

Locator. The PL-VF PLS Locator is specially designed to detect conductors such as buried pipes & cables. This

device may detect buried power cables, CATV cables, gas and water pipes, sewer lines, telecommunication

lines, fiber optic cables with sheath, sondes, inspection camera transmitters. You have chosen a quality

product that is designed for years of field use without the need for annual or periodic calibration and service.

The basic principle of the locator's operation is as follows:

The

ransmiTTer

emits a signal to a conductive cable or pipe. The

eceiver

detects the electromagnetic field

that is generated by the transmitted signal. You can locate the relative position of the buried utility by

following the tracing signal.

For safely & to help ensure the best locating results, please read & understand the manual in its entirety

before using the product.

SubSurface Instruments, Inc. shall not be liable to Distributor, Re Seller, or any other person for any

incidental, indirect, special, exemplary or consequential damages, or injury of any type whatsoever, and

caused directly or indirectly by Products sold or supplied by SubSurface Instruments, Inc..

Failure to follow these warning could result in serious injury or death.

Only persons qualified and trained to operate cable & pipe locators may operate this equipment.

Follow appropriate safety procedure, your companies policies and applicable safety codes and/or laws.

Do not connect to utilities, cables or pipes without authorization and training.

Use tool only for intended purpose as described in this manual

Do not expose tool to rain or moisture.

Do not expose to hazardous chemicals, hazardous gas or explosive environment.

SHOCK HAZARD - Lethal voltages may be present at the transmitter's output. Turn off transmitter before

touching test lead or any un-insulated conductor. Make connection to ground and target conductor before

turning on transmitter.

SHOCK HAZARD - Do not connect to live voltage or active utility lines. De-energize any circuits in or around

the work area.

This tool is designed to detect electromagnetic field emitted from cables and buried metallic utilities. There are

buried cables, pipes, and utilities this instrument CANNOT detect.

LOCATING is not an exact science. The only certain way to be sure of the existence, location, or depth of

buried utilities is to carefully expose (dig up) the utility.

WARNING!

WARNING!
WARNING!

ntroduCtion

isClaimer

iability

mportant

otiCes

Содержание PL-VF Series





























Результаты поиска

Содержание PL-VF Series

Отзывы:

Похожие инструкции для PL-VF Series

Бренды по названию

Популярные бренды

SubSurface Instruments PL-VF Series, Руководство пользователя

Результаты поиска

Содержание PL-VF Series

Отзывы:

Похожие инструкции для PL-VF Series

Бренды по названию

Популярные бренды