background image

6 OF 12

PART NUMBER

H001SFJ600

ISSUE

00

DATE

18 Jul 2013

SUBARU OF AMERICA

LOCK

ACC

ON

ST

ART

ACC

ON

ST

AR

T

LOCK

7

NOTE: Use caution while installing the wiring harness, be sure to

route and attach the harness away from sharp metal surfaces.

8-PIN IGNITION SWITCH CONNECTIONS

1.  Adjust the tilt/telescoping steering column all the way out and down.

2.  Locate the 8-pin ignition switch connector on the right side of the steering

column and unplug.  Carefully pull the connector down and toward the steering

wheel.  (FIGURE O)

3. Plug the remote start ignition harness 8-pin female connector into the vehicle’s

ignition switch.  (FIGURE P)

4.  Carefully fold back the remote start harness foam wrapped 8-pin male

connector.  Plug the previously unplugged vehicle’s female ignition switch

connector into the remote start ignition harness foam wrapped 8-pin male

connector (FIGURE P).

5. Route the remote start ignition harness over the top of the vehicle’s ignition

harness (hard shell cover) towards the firewall.

6. Using four of the supplied 39cm (15”) tie wraps, secure the remote start

ignition harness to the following. (FIGURE Q)

Tie wrap #1 - Secure the mated vehicle female ignition switch connector and

remote start ignition harness 8-pin male connectors to the existing factory

wiring harness located lower front of the steering column.  NOTE: The tie

wrap should secure around the foam covered mated connectors, not the

wiring.

Tie wrap #2 - Secure the remote start ignition harness to the vehicle’s steering

column harness hard shell cover.

Tie wrap #3 - Secure the remote start ignition harness to the vehicle’s steering

column harness hard shell cover in front of the remote start harness convoluted

tubing area.

Tie wrap #4 - Secure the remote start ignition harness to the vehicle’s steering

column harness behind the hard shell cover and remote start harness

convoluted tubing area.

NOTE: Do not secure tie wraps to the convoluted tubing covered area of the

remote start ignition harness.

WIRE HARNESS CONNECTIONS

FIGURE O

FIGURE P

FIGURE Q

LOCK

ACC

ON

ST

ART

1

2

3

4

Convoluted

Tubing

8-Pin Remote Start
Harness Female
Connector

8-Pin Factory
Harness Female
Connector

8-Pin Remote Start
Harness Male
Connector

Содержание H001SFJ600

























Отзывы: