manualshive.com logo in svg

Stulz BNB1000, Руководство по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Stulz BNB1000 Скачать руководство пользователя страница 17

(©January, 2008)

Air Technology Systems, Inc.

BNB Ultrasonic Humidifier Installation, Operation & Maintenance Manual

5-2

Replacing transducer.

After about 10,000 to 15,000
hours of operation.

Sect. 5.4.3 on
page 5-8

Replacing nebulizer print
plate.

If damaged or upon failure.

Replacing water supply
solenoid valve.

Replacing float switches.

Replacing printed circuit
board.

Sect. 5.4.4 on
page 5-9

Adjustable wrenches (2)

Phillips screwdriver

7/32” Nut driver

Soft cleaning cloth

Small brush

Diagonal wire cutter

Item

Cycle

Description

Necessary Tools

None

Air filter cleaning.

About once a week depending
on the extent of contamination.
The interval should be short-
ened if environmental condi-
tions are particurlarly dusty

Sect. 5.2.1 on
page 5-3

Check water tank
interior, mist blow tubes
and electrical parts.

Once a month or as required
if environment is dusty or
water suppy quality is poor.

Sect. 5.2.2 on
page 5-3

Routine Maintenance

Replacing Parts

5.2

Maintenance Items and Necessary Tools

If damaged or upon failure.
Also recommended when
replacing transducer

Содержание BNB1000





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды