background image

1

26

Power requirements

INDEX

Introduction

Read the User Guide

Unpacking

Safety Instructions

Rack mounting kit for the Horizon.

CONTROLS & FEATURES, Front Panel

Mono input channels

Stereo input channels

Output section

Rear panel

USING YOUR HORIZON

Getting sound out of you Horizon

Setting up a microphone

Adding Effects

Using the channel compressor

Connecting stage monitors

REFERENCE

General hints and tips

Cleaning your Horizon

Loudspeaker power ratings

Ventilation

Feed Back

Sound sources

Headphones

Connector wiring

Suggested set-up diagrams

Trouble shooting

Glossary of technical terms

Warranty

Service Information

Environmental Protection

Technical specification

Block diagram

Voltage

230V Model:                                          220-240V ~ 50/60Hz

115V Model:                                          110-120V ~ 50/60Hz

Power Consumption:                            At idle or  low power:                           60W

                                                                Both amplifiers at 1/8 power*:            450Watts 

                                                                Both amplifiers at 1/3power**:            900Watts 

Fuse:

230V Model:                                          T8AL 250V 20x5mm

115V Model:                                          15A 3AG  0.25

x 1.25

Dimensions                                           2012                                                       2020

Width mm(inches)                                478(18.9)                                              678(26.7)

Depth mm(inches)                                497(19.6)                                              497(19.6)

Height mm(inches)                               154(6.1)                                                154(6.1)

19

” 

Rack Mounting:                              12 rack spaces                                     N/A

Weight (net/shipping): 

Net kg(lb)                                               13.4 (29.5)                                            15 (33)

Shipping kg(lb )                                     16 (35.2)                                               18 (39.6)

*Equivalent to program material at full power into 4 ohm speakers with occasional clipping 

*Equivalent to program material at full power into 4 ohm speakers with frequent clipping

2

2

2

2

15

15

16

16

16

16

17

18

16

27

24

23

23

23

20

20

13

13

14

14

14

2

3

3

5

7

12

Содержание Horizon 2012
















Отзывы: