manualshive.com logo in svg

Stuart Turner monsoon extra, Руководство по установке

Поделиться
Скачать
Stuart Turner monsoon extra Скачать руководство пользователя страница 13

PUMPS

PUMPS

1. System Flushing

This pump incorporates push-in connectors and plastic components that 
must not come into contact with solder flux, acid-based descalents or 
aggressive cleaning agents.  The pipework system should be flushed out 
prior to the pump being connected to ensure any contaminants/chemical 
residues and foreign bodies are removed from elsewhere in the system.

2. Water Supply

Always ensure that water storage capacity is adequate to meet the 
demand.  Ensure the pump chamber is full of water before starting the 
pump.  Failure to do this could result in seal damage.  To ensure dry 
running does not occur the pump must be primed as described in priming 
section.  

Do not run pump dry.

3.

Priming
The pump must be primed (filled with water) before starting.  Turn on water supply, 
prime and vent the pump by unscrewing the priming plug (Figs. 15, 16 & 17) slowly 
until all air escapes and water emerges.  Re-tighten the plug.

- 13 -

N1.3 bar Single

Fig. 15

N2.4 and N2.9 bar Single

Fig. 16

N3.7 bar Single

Fig. 17

Priming
Plug

Priming
Plug

Priming
Plug

Содержание monsoon extra





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды