Stryker Zoom 2040 Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 221

background image

74

2040-309-002 REV B

www.stryker.com

Return To Table of Contents

Tools Required:

•  T27 Torx
•  1/2” Box End Wrench
•  # 2 Phillips Screwdriver
•  Wire Cutters
•  Small Flat Blade Screwdriver
•  5/16” Nut Driver

Procedure:
1. If it has not already been done, follow steps 1 - 7 of the “Zoom® Option Control Bar Potentiometer Replacement

Procedure on

.

2.  Ensure the battery on/off switch is in the “Off” position (LED is Off).
3.  Hold down the yellow button on the back of the display CPU board.
4.  With the switch depressed, move the battery power on/off switch to the “ON” position (LED will light) and continue

holding for three seconds.

5. Press and hold the yellow button on the back of the display CPU board.
6. Move the battery power on/off switch to the “on” position (LED will light) and continue holding switch for three

seconds.

7.  Verify the “Engage Drive Wheel” led at the head end display housing is flashing.
8.  Move the battery power on/off switch back to the “Off” position (all LED’s will go out).
9.  Close the drive box.
10.  Ensure the control bar is in the center of travel by pushing and pulling the bar, then returning the bar to the neutral

position.

11. With no objects touching the control bar, turn the battery power on/off switch to the “On” position.
12. The three LED’s on the front of the bed will flash initially to show the battery voltage of the bed by lighting zero,

one, two, or three LED’s.

13. After the battery charge has been displayed by the three LED’s, all three LED’s will flash twice.
14. After all three LED’s have flashed twice, push the drive handle to the full forward position. Hold the drive handle

in the full forward position until all three LED’s flash twice again (3 seconds).

15.  The “ENGAGE DRIVE WHEEL” LED will flash once.
16.  The control bar potentiometer is calibrated.
17.  Return the control bar to the neutral position.
18.  Grasp the control bar and squeeze either motion switch without moving the control bar forward or backward.
19.  Verify the bed does not move.
20.  Standing at the head end of the bed, grasp the control bar and squeeze either motion switch, then push the control

bar forward.

21. Verify the bed moves forward.
22. Standing at the head end of the bed, grasp the control bar and squeeze either motion switch, then pull the control

bar backwards.

23.  Verify the bed moves backward.
24.  Move the battery power on/off switch “Off”, wait a few seconds, then back “On” again.
25.  Repeat steps 18-23 to verify that the burn in procedure was performed correctly.

Control Bar Potentiometer “Burn-In” Procedure

Service information

«
...
72
73
74
75
76
...
»

Содержание Zoom 2040






























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Zoom 2040

Бренд: Navman Страницы: 17

Бренд: GALBIATI Страницы: 20

Бренд: Xtool Страницы: 8

Бренд: StarDental Страницы: 2

Бренд: USC Страницы: 29

Бренд: DALBO Страницы: 27

Infinity Wash XL

Бренд: Coemar Страницы: 6

Бренд: Cleaver Scientific Страницы: 41

Бренд: WESTEK Страницы: 4

Бренд: Kalco Lighting Страницы: 6

TRICEPS EXTENSION

Бренд: ETENON Fitness Страницы: 26

Бренд: Wieland Страницы: 15

Бренд: Interacoustics Страницы: 2

Бренд: Augmedics Страницы: 31

Бренд: EuroLite Страницы: 36

Бренд: Vari Lite Страницы: 14

Clinician Premiere Series

Бренд: OAKWORKS Страницы: 29

Бренд: Aeware Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды