58
2040-309-002 REV B
Tools Required:
• #2 Phillips Screwdriver.
• Side Cutters.
• 5/16” Socket Wrench.
• Bungee Cord (or equivalent).
• 5/16” Nut Driver.
• Floor Jack.
• 2 x 4 (or Equivalent).
Procedure:
Note
If you need more space to work under the base frame, place a 2 x 4 across the base frame rails and use a floor jack
to raise the base frame off the floor.
1. Unplug the power cord from the wall socket and push the battery power on/off switch to the “Off” position.
2. Using a 5/16” socket wrench, remove the five bolts holding the lower lift cover to the base and remove the cover.
3. Using a #2 Phillips screwdriver, remove the three screws holding the upper lift cover to the base. If necessary, hold
the covers out of the way by using bungee cords (or the equivalent) to secure them to the litter top.
4. Using side cutters, cut the cable ties holding the power and sensor coil cords to the base. Remove the ground wire
coming from the sensor cord that is attached to the base (note the star washer arrangement).
5. Disconnect the cables going to the motor and the lift potentiometer (at the head end, the sensor cord is also
attached to the brake switch sensor).
6. Pull both cords up through the frame of the bed and the lift housing.
7. Using a 5/16” socket wrench, remove the two screws (A) holding the cable clamps to the top of the lift housing.
8. Using a 5/16” socket wrench, remove the two screws (B) securing the cable clamps to the underside of the header
crossbar assembly.
9. Pull both coil cords up through the header crossbar assembly.
10. Disconnect the power and sensor coil cords from the connectors.
11. The cords should now be completely removed from the bed. Reverse the above steps to install the new power and
sensor cords.
CAUTION
When the power and sensor coil cords are being replaced, secure the cable clamps to the cords at the first coil both
on the top and on the bottom to ensure there is not too much slack in the cords between the top of the lift housing
assembly and the bottom of the header crossbar. Be sure the clamps are fastened at exactly the correct angle, as
shown by the arrows in the illustration on the next page. Arrange the cords exactly as shown in the illustration (left in
front of right). If this is not done correctly, damage to the cords will result.
Power and Sensor Coil Cord Replacement
Service Information
Содержание Zoom 2040
