manualshive.com logo in svg

Stryker 3002, Руководство по обслуживанию

Поделиться
Скачать
Stryker 3002 Скачать руководство пользователя страница 53

Return To Table of Contents

www.stryker.com

3006-409-006 REV C

53

Note

Do not allow the ball nut assembly to come off the drive screw. The ball nut will be shipped attached to the drive screw 
and retained in position during shipment. Remove the wire ties after installing the drive screw assembly.

12.  Remove the thrust washers and bearing from the head end of the drive screw and set them aside.
13.  Reverse the above steps to install the replacement ball screw assembly.

Note

Apply grease to all bearing areas.

 CAUTION

Verify the fowler motor stops properly at both upper and lower electric limits. If it does not, 

refer to 

page 49

.

HEAD MOTOR BRAKE/CLUTCH REPLACEMENT

TOOLS REQUIRED:

•  3/8” Socket Wrench
•  Snap Ring Pliers
•  9/16” Socket Wrench
•  9/16” Box End Wrench
•  Wire Cutters

PROCEDURE:

1.  Remove the fowler motor (

page 50

).

2.  Using snap ring pliers, remove the snap ring from the motor shaft.

 CAUTION

The brake/clutch is spring-loaded. Use caution when removing the snap ring so the parts do not drop to the floor.

3.  Remove the old brake/clutch from the motor and discard it.
4.  Using a 9/16” socket wrench and a 9/16” box end wrench, remove the nut, bolt and washers from the new 

brake/clutch.

5.  Install the new brake/clutch onto the motor. It may be necessary to turn the motor shaft to line up the key way with 

the brake/clutch.

6.  Using the snap ring pliers, install the new snap ring.
7.  Using the wire cutters, remove the four wire ties from the new brake/clutch.
8.  Reinstall the fowler motor (

page 50

).

9.  Test the bed for proper operation before returning it to service.

FOWLER MOTOR BALL SCREW ASSEMBLY REPLACEMENT (CONTINUED)

Service Information

Содержание 3002






















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды