background image

OVERVIEW 

 



These Structural Concepts merchandisers are 
designed to merchandise packaged products at 
ambient temperatures. 



Cases should be installed and operated according to 
this operating manual’s instructions to insure proper 
performance.  Improper use will void warranty. 

 

CASE TYPE 

 

This unit is designed for the display of products in ambient 
store conditions where temperatures and humidity are 
maintained within a specific range.   

 



For Type 1 Conditions (most cases): ambient 
conditions are to be at 55% maximum humidity and  
maximum temperatures of 75 °F (24 °C).   



For Type 2 Conditions: ambient conditions are to be 
at 60% maximum humidity and maximum 
temperatures of 80 °F (27 °C).   



If unsure if unit is designed for Type 1 or 2, see tag 
next to serial label.  See 

SERIAL LABEL LOCATION 

& INFORMATION LISTED / TECH INFO & SERVICE

 

section in this manual for sample serial labels.

 

 

COMPLIANCE 

 



Performance issues when in violation of applicable 
NEC, federal, state and local electrical and plumbing 
codes are not covered by warranty. 

 

WARNINGS 

 



This sheet contains important warnings to prevent 
injury or death. 



Please read carefully! 

 

PRECAUTIONS, CORD/PLUG MAINTENANCE & 
WIRING DIAGRAM INFORMATION 

 



See next page for 

PRECAUTIONS, CORD/PLUG 

MAINTENANCE 

and

 WIRING DIAGRAM

 information.

 

OVERVIEW / TYPE / COMPLIANCE / WARNINGS / PRECAUTIONS / WIRING / PLUGS 

WARNING  

  

Risk of electric shock. Disconnect power before servicing unit. 

CAUTION!  More than one source of electrical supply is  

employed with units that have separate circuits.   

Disconnect ALL ELECTRICAL SOURCES before servicing. 

 

WARNING 

ELECTRICAL 

  HAZARD

 

COMPLIANCE 

 

This equipment MUST be installed in compliance with 

all applicable NEC, federal, state and local electrical codes. 

CAUTION!  LAMP REPLACEMENT GUIDELINES 

 

LED lamps reflect specific size, shape and overall design.   

Any replacements must meet factory specifications. 

 

Hera® / Fluorescent lamps have been treated to resist breakage            

and must be replaced with similarly treated lamps. 

CAUTION 

CAUTION!  GFCI BREAKER USE REQUIREMENT 

 

If N.E.C. (National Electric Code) or your local code                                    

requires GFCI (Ground Fault Circuit Interrupter) protection,                             

you MUST use a GFCI breaker in lieu of a GFCI receptacle. 

CAUTION!  POWER CORD AND PLUG MAINTENANCE 

 

 

Risk of electric shock.  If cord or plug becomes damaged,                       

replace only with cord and plug of same type.   

Содержание B3632D














Отзывы: