background image

OVERVIEW 

 

 

These Structural Concepts merchandisers are 

designed to merchandise packaged products at 

ambient temperatures. 

 

Cases should be installed and operated according to 

this operating manual’s instructions to insure proper 

performance. Improper use will void warranty. 

 

TYPE I ENVIRONMENTAL CONDITIONS 

 

This unit is designed for the display of products in ambient 

store conditions where temperatures and humidity are 

maintained within a specific range.   

 

 

Type 1 Conditions (this case): ambient conditions are 

to be at 55% maximum humidity and  maximum 

temperatures of 75 °F (24 °C).  

 

This merchandiser is designed to display non-

hazardous, packaged/unpackaged bakery products. 

 

COMPLIANCE 

 

 

Performance issues when in violation of applicable 

NEC, federal, state and local electrical codes are not 

covered by warranty. 

 

See below compliance guideline.

 

 

WIRING DIAGRAM 

 

 

Each case has its own wiring diagram folded and in its 

own packet. 

 

Wiring diagram placement may vary; it may be placed 

near ballast box, field wiring box, raceway cover, or 

other related location.

 

OVERVIEW / TYPE I ENVIRONMENTAL CONDITIONS / COMPLIANCE 

COMPLIANCE 

 

This equipment MUST be installed and operated in  

compliance with all applicable NEC,                         

federal, state and local electrical codes. 

ATTENTION                 

CONTRACTORS

 

WARNING  

  

Risk of electric shock. Only authorized electrical contractors  

should perform field wiring box connectivity duties. 

 

WARNING 

ELECTRICAL 

  HAZARD

 

CAUTION!  POWER CORD AND PLUG MAINTENANCE 

 

 Risk of electric shock.  Any appliances that are sitting on or around 

this unit may have a cord or plug that can become damaged.  

In such instances, replace only with cord and plug of same type.   

WARNING: This product can expose you to chemicals, including 

 Urethane (Ethyl Carbamate), which are known to the state of  

California to cause cancer and birth defects or other reproductive  

harm. For more information go to P65Warnings.ca.gov.

 

WIRING DIAGRAM FORMAT & LOCATION 

 

 

Each case has its own wiring diagram folded and in its own packet. 

 

Wiring diagram placement may vary; it may be placed near ballast 

box,  field wiring box, raceway cover, or other related location. 

 

See sample wiring diagram at left (for illustrative purposes only). 

Содержание Addenda 20-53882















Отзывы: