background image

throat side of the racquet. 

 
Clamping a racquet. 

 
HEAD SIDE SUPPORT 
The racquet clamp is adjusted to the height of the racquet with the adjustable counter support.  
Because the clamp can swivel in the slot it can clamp a considerable range without the need to adjust 
the counter support. 
 
* Fast clamp system: 

 

 
The pictures show the actions  needed to clamp the racquet: 
- Switch the lever forward. 
- Lift the counter support out of the slot. 
- Rotate the clamp with the flat side towards the racquet. 
 
Clamping the racquet goes as follows: 
- Rotate the clamp above the racquet with the counter support in the slot. 
- Switch the lever to the  vertical position. 
- Rotate the upper nut by hand until it hits the clamp. 
- Switch the lever further to the back. 
 
If the clamping force is not as desired switch back to the vertical position adjust the nut and switch 
the lever backwards again. 
 
THROATSIDE SUPPORT. 

 

 
 
 
 
 
 
 
 

The racquet is clamped with a transparent crossbar so that there is good view on the grommet holes in 
the bridge of the racquet. 
 
IMPORTANT: The cross bar will bend considerably when you clamp a racquet, this is not a problem. 
 

BUT: Take care not to over-tighten the clamp, because there is no need to use much clamping 
force.  

Содержание MS140L














Отзывы: