Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 327

background image

Commissioning

117

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

5.12.3.3 Connect emergency brake valve

If the machine is torn off, the ripcord will actuate the emergency brake valve. The hydraulic oil then
flows from the pressure accumulator into the brake cylinders, thus initiating the braking process.

1.



Fasten the ripcord (1) to the tractor such that in case of the machine being torn off, the ripcord
(1) is in a horizontal position between tractor and machine.

(1)

Ripcord

(2)

Coupling box

(3)

Emergency brake valve

(4)

Pressure accumulator

(5)

Brake cylinder

(6)

Brake drum

(7)

Drain valve

Fig. 62

Couple after emergency braking:

1.

Connect the brake hose to the tractor.

2.

Set the brake control valve at the tractor such that the hydraulic oil can flow back to the tractor.

3.

Press the drain valve (7) at the emergency brake valve (3).



The hydraulic oil flows back to the tractor and the pressure accumulator (4) is depressurised.

4.

Insert the ripcord (1) with the clip connector into the borehole of the operating lever.

5.

Set the operating lever back to its initial position.

6.

Actuate the brake system of the machine several times.



The pressure accumulator (4) is filled and the emergency brake valve (3) is ready for operation
again.

«
...
115
116
117
118
119
...
»

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Giga-Vitesse CFS 3602

Бренд: Varec Страницы: 74

Бренд: Halyard Страницы: 84

Бренд: PAIDI Страницы: 48

Бренд: BACtrack Страницы: 13

Бренд: TA Instruments Страницы: 35

Бренд: Califone Страницы: 7

Бренд: CALITEK Страницы: 16

Бренд: LAHTI PRO Страницы: 20

Бренд: LAHTI PRO Страницы: 16

Бренд: J&M Страницы: 53

Бренд: Qazqa Страницы: 2

Бренд: Rainbow Страницы: 18

Бренд: dbx Страницы: 2

Бренд: Eagle Group Страницы: 8

Бренд: IBS Scherer Страницы: 64

Бренд: Major tech Страницы: 12

Бренд: mychway Страницы: 56

Бренд: JBM Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды