background image

Safety

Conventions used in this Guide

Page 3

© Copyright 2020 Stratasys. All rights reserved.

Safety

Conventions used in this Guide

Below are safety-related symbols used on the extraction system and referred to within this 

manual.

Electrical Safety

The air extraction system has been designed to meet the safety requirements of the Essential 

Health and Safety Requirements of the Machinery Directive 2006/42/EC.
Disconnect the power from the system before opening the cover.
To reduce the risk of fire, electric shock, or injury:
1. Always disconnect the system from the main power supply before servicing.
2. Use this system only as described in this manual.
3. Connect the system to a properly grounded outlet.

Warning/Danger:

Refers dangerous situations which will result in death or severe injury. Refer to this 

guide before proceeding when this symbol is displayed on the system.

Caution:

Refers to a possibly harmful situation. If not avoided, damage could be caused to the 

system or its environment. Refer to this guide before proceeding when this symbol is 

displayed on the system.

Important:

Refers to tips and other particularly useful information. This does not indicate a 

dangerous or harmful situation.

Содержание ProAero


















Отзывы: