Stratasys Eden260V Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 202

background image

Eden260V User Guide

2 Safety

DOC-32020 Rev. F

2-3

UV-Lamp Overheating
Protection

The power supplied to the UV lamp, the tray heater and the
motion motors is turned off if the temperature around the lamp
reaches 90°C (194°F). A label on the UV-lamp cover indicates if
the temperature has exceeded 65°C (150°F).

Grounded Chassis

The chassis of the printer is grounded, to prevent electrical shock.

Note:

The power outlet must be grounded in accordance with the

local electric code to provide this protection.

If the printer is not used as specified in this guide, these safety features may not provide
adequate protection.

Symbols and Warning Labels

The following table lists the warning labels located on or in the printer.

Warning Symbol

Meaning

Location

Comments

Hazard (general)

On the name plate on the
back of the printer.

Read the instructions in
this document before
operating the printer.

Hot surface

On the print block.

Risk of burns. Do not
touch this surface after
printing.

High voltage

Near the UV lamp
connectors.

Near the power-supply
enclosures.

Risk of electric shock.
Disconnect the power
before servicing.

Ultraviolet radiation Near the UV lamps.

Risk of injury to skin and
eyes from ultraviolet
radiation. Disconnect the
power before servicing.

«
...
15
16
17
18
19
...
»

Содержание Eden260V











































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Eden260V

Бренд: m3d Страницы: 23

Бренд: m3d Страницы: 26

Бренд: Tally Страницы: 202

ExpressCard 2000

Бренд: Magtek Страницы: 25

Бренд: Oki Страницы: 48

Бренд: Oki Страницы: 65

Бренд: Oki Страницы: 44

Бренд: Oki Страницы: 36

Бренд: OHAUS Страницы: 28

Бренд: Zonestar Страницы: 25

Бренд: Oki Страницы: 156

Posligne ODP-1000

Бренд: AURES Страницы: 4

Бренд: Lexmark Страницы: 142

Бренд: SEWOO Страницы: 8

Бренд: Skynet Страницы: 18

Бренд: Epson Страницы: 15

Бренд: Citizen Страницы: 24

Quatro ID Card Printer

Бренд: FARGO electronics Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды