background image

UsEr mAnUAl

w w w. s t r A n D l i g h t i n g .co m

AcclAim lED FrEsnEl   

22

All Vari-lite and Strand lighting luminaires are governed by the same fan 

speed versus noise levels and maximum power output rules as detailed 

below. The noise related to these levels conforms to noise criteria levels 

detailed within the document. 
There are three control parameters that can can be selected separately or 

in conjunction when permitted to manage fan speed versus noise levels 

and maximum power output.

NOTE:

 Not all fi xture have all modes or functions.  Refer to DMX map and/

or user interface menu tree to verify the modes and functions in your 

fi xture.

FAN VERSUS OUTPUT PRESET MODES

These modes are selectable at either / or the fi xtures DMX control chan-

nel or via the fi xture user interface screen. 

Boost mode –

 LED output boosted to >120% of standard output fan 

speeds increased manage heat level of LED (may be limited to only run 

for XXhrs). Fixture will not exceed NC45 – NC55 sound levels in this mode

Standard mode -

 Full LED Fan Spin at top speed (loudest set-

ting). Fixture will not exceed NC40 sound levels in this mode.

Studio mode -

 Fan speed reduced to appropriate amount to reduce 

dB  levels >10% of full speed + LED @ max output approximately 80% 

of Standard output at appropriate level to ensure LED work at optimum 

temperature and output effi  ciency (fan speed remains at a constant speed and do not ramp up or down) NC35.

Whisper mode - 

Fan speed reduced to appropriate amount to reduce dB levels to >30% of the full speed + LED Max out-

put approximately 60% of Standard output at appropriate level to ensure LED work at optimum temperature and output 

effi  ciency (Fan speed remains at a constant speed and do not ramp up or down) NC25.

Silent mode –

 ideally Fans do not spin + output capped at appropriate level to ensure LED work at optimum temperature 

and output effi  ciency (Fan should never switch on in this mode or change speed if they on) NC15 target level. 

90

0

10

20

30

40

50

60

70

80

63

125

250

500

1000

2000

4000

8000

NC 15

NC 20

NC 25

NC 30

NC 35

NC 40

NC 45

NC 50

NC 55

NC 55

NC 55

NC 55

FREQUENCY (HZ)

SOUND PRES

SURE LEVEL (

dB)

MOde

Led 

OUTpUT

FAn Speed 

nOiSe 

CRiTeRiOn

eQUiVALenT SOUnd 

LeVeL dBA (@3M)

Boost Mode

>100%

Boosted fan speed constant 

NC45

50

Standard Mode

Full 100%

Full 100% constant

NC40

45

Studio Mode

80%

Appropriate speed to reduce 

dB levels >10% of full speed

NC35

40

Whisper Mode

60%

Appropriate speed to reduce 

dB levels >30% of full speed

NC25

35

Silent Mode 

TBC

Fan off 

NC15 

25

nOiSe 

CRiTeRiOn

OCTAVe BAnd CenTeR FReQUenCY (HZ)

63

125

250

500

1000

2000

4000

8000

SOUnd pReSSURe LeVeLS (dB)

NC-15 

47 

36 

29 

22 

17 

14 

12 

11

NC-20 

51 

40 

33 

26 

22 

19 

17 

16

NC-25 

54 

44 

37 

31 

27 

24 

22 

21

NC-30 

57 

48 

41 

35 

31 

29 

28 

27

NC-35 

60 

52 

45 

40 

36 

34 

33 

32

NC-40 

64 

56 

50 

45 

41 

39 

38 

37

NC-45 

67 

60 

54 

49 

46 

44 

43 

42

NC-50 

71 

64 

58 

54 

51 

49 

48 

47

NC-55 

74 

67 

62 

58 

56 

54 

53 

52

NC-60 

77 

71 

67 

63 

61 

59 

58 

57

NC-65 

80 

75 

71 

68 

66 

64 

63 

62

NC-70 

83 

79 

75 

72 

71 

70 

69 

68

FAN SPEED AND CONTROL

Appendix B  

Содержание Acclaim LED Fresnel
























Отзывы: