background image

 

 

SPECIFICATION 

 

 

Width:12m 

Length:12m 

Height:4.5m 

 

IMPORTANT ---- READ MANUAL FIRST 

 

 

Improper  site  preparation,  Assembly  and  Maintenance  may  invalidate  warranty  and  cause 
unnecessary and costly mistake. If you have any questions contact your local dealer. 

 

For User Friendly assembly we have identified each individual component with the part code as 
indicated in the parts list. Please refer to the part code numbers and drawing to ensure problem free 
assembly. 

 

It’s necessary to tighten the roof fabric enough to avoid “hammocks” on the roof and also re-tighten 
once or twice again after a few months of use. This is important when assembly in cold weather 
(autumn and winter) because the fabric is stiff then and when we got the sun and warm weather 
afterwards it will make the fabric “slack” again and need to be re-tighten before next winter. 

 

It’s the owners responsibility to take of snow immediately if not slide off by itself. 

 

READ ALL INSTRUCTIONS BEFORE ASSEMBLY 

 
 

 

1.

 

Keep work area clean. Cluttered areas invite injuries. Do not set up near snow drifts, in 
slippery places, in high winds, or wet location. 

2.

 

Keep children away. All children should be kept away from the work area. 

3.

 

Don’t over reach. Keep proper footing and balance at all times. 

4.

 

Do  not  assemble  in  under  the  influence  of  alcohol  or  drugs.  Read  warning  labels  on 
prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there 
is any doubt, do not assemble. 

5.

 

Be aware of possible windy conditions; fasten the bases in concrete if these conditions are likely 
to occur. Remove the cover during hurricane. 

6.

 

Be careful with power and heat sources. Do not keep heat sources near the tarpaulin. Do not 
expose to open flame. 

7.

 

Be aware of personal safety during assembly and use. Be careful not to pinch fingers with clips 
and tubes when assembling: when using makes sure there is adequate ventilation for exhaust 
and other dangerous fumes. 

Содержание C4040S











Отзывы: