background image

 

 

 

Highly Recommended  

1.

 

All container canopy covers need to be removed during windstorm of 60 mph, 
leaving frame assembled. 

Customer responsibility

.  

2.

 

All container canopy covers need to be removed before a snowstorm of 1-2 inches 
(for single truss Shipping container roofs) and 3-4 inches (for double truss Shipping 
container roofs), leaving the frame assembled. 

Customer responsibility

3.

 

It is highly recommended for customers who live in snow states and cities to use 
double truss framing instead of Single truss framing. 

Customer responsibility.

 

4.

 

It’s the owner's responsibility to shovel snow off the canopy rooftop. 

5.

 

All containers need to be anchored to the ground in each opposite corner sides. 

Customer responsibility

6.

 

All of our products fall under the temporary structure category/storage ragtops. 

Return Policy:

 Any product can be returned within 7 calendar days after arrival; shipping 

expenses are not refundable. For more information, please refer to the 

Return and refund 

policy

 page.  

 

About lifespan:  

Tarp lifespan: 

7-10 years*

 

Frame Lifespan: 

+15 years*

 

*The term "lifespan" refers to the durability of the materials themselves, not to the 
structural integrity of the canopy once assembled. 

 

Содержание 40x40x15












Отзывы: