Stocks AG Turbo Jet 10 Скачать руководство пользователя страница 43

 

 

White Standard Spacers –

There are 2 x 3mm white small end  

spacers, 4 x white mid spacers, and 3 x white large spacers – these always stay in the same order and 
position whatever the combination of 5mm Small Seed rolls and black roll spacers.   

 

 
 
 
5mm Small Seed Rolls and Stainless Steel Discs. 

One stainless disc is fitted to each side of the 5mm small seed rolls. They are used to reduce the 
friction element between the small seed rolls and the plastic spacers that are to each side of them. 

Note. 

They are not used with grass rolls 

The feed rolls have square holes in the middle 
that locate on the square feed shaft, and 
rotate with the feed shaft, powered by the 
12v electric feed motor.  
 
The plastic spacers have round clearance 
holes through the middle and are not driven 
and thus do not revolve and an element of 
friction may occur between the revolving feed roll and the stationary plastic spacer. 
To eliminate this friction, the stainless disc also has a square hole and locates on the drive shaft and 
thus rotates with the feed roll. Any friction is now between the rotating stainless disc and the static 
plastic spacer. 

 
 
 
Note.  Always assemble the rolls and spacers with a stainless steel disc on each side of the 5mm 
feed rolls.

  

Use 1 stainless disc each side of the feed rolls if a single feed roll is used - 
if 2 or 3 feed rolls per outlet are used, fit 1 stainless steel disc to each side 
of the outer feed rolls. Do not fit the steel disc between the feed rolls.  

Note. 

The total bank of rolls and spacers and steel discs should not 

protrude beyond the end of the feed block. 
 
 

Содержание Turbo Jet 10



















































Отзывы: