manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

CPU subsystem_Vectored interrupt controller (VIC)

RM0082

98/844

Doc ID 018672 Rev 1

         

8.6.10 VICSOFTINTCLEAR register

The VICSOFTINTCLEAR is a WO register which allows to clear bits in the VICSOFTINT 
register (

Section 8.6.9: VICSOFTINT register

). The VICSOFTINTCLEAR bit assignments 

are given in 

Table 36

.

         

8.6.11 VICPROTECTION 

register

The VICPROTECTION is a RW register which allows to enable or disable protected register 
access. The VICPROTECTION bit assignments are given in 

Table 37

.

         

Note:

This register is cleared on reset, and it can only be accessed in privileged mode. If the AHB 
master cannot generate accurate protection information, this register shall leaved in its reset 
state (protection disabled) in order to enable User mode access.

8.6.12 VICVECTADDR register

The VICVECTADDR (vector address) is a RW register which contains the ISR address of 
the currently active interrupt. The VICVECTADDR bit assignments are given in 

Table 38

.

Table 35.

VICSOFTINT register bit assignments

Bit

Name

Reset 
value

Description

[31:00]

SoftInt

32’h0

Each bit is associated to a source interrupt.

Setting a bit, a software interrupt for the specific source 
interrupt is generated before interrupt masking.

Table 36.

VICSOFTINTCLEAR register bit assignments

Bit

Name

Reset 
value

Description

[31:00]

SoftIntClear

-

Each bit is associated to an interrupt line.

Writing a 1‘b1 in a bit, the corresponding bit in the 
VICSOFTINT register is cleared.

Writing a 1‘b0 has no effect.

Table 37.

VICPROTECTION register bit assignments

Bit

Name

Reset 
value

Description

[31:01]

Reserved -

Read: 

undefined. Write: should be zero.

[00]

Protection

1’h0

Enable/disable protected register access.

Setting this bit, protected register access is enabled 
ensuring that only privileged mode accesses, reads 
and writes, can access the interrupt controller 
registers. 

Clearing this bit, protected register access is disabled 
allowing both user mode and privileged mode to 
access the registers.

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

Gardena 4040 Operating Instructions Manual preview
4040
Бренд: Gardena Страницы: 100
S-COM 7K Manual preview
7K
Бренд: S-COM Страницы: 400
Danfoss VLT HVAC Operating Instructions Manual preview
VLT HVAC
Бренд: Danfoss Страницы: 85
Danfoss VLT Decentral FCD 300 Operating Instructions Manual preview
VLT Decentral FCD 300
Бренд: Danfoss Страницы: 112
Danfoss AME 55QM Datasheet preview
AME 55QM
Бренд: Danfoss Страницы: 4
Danfoss VLT 6000 series Manual preview
VLT 6000 series
Бренд: Danfoss Страницы: 27
Danfoss AME 20 Operating Manual preview
AME 20
Бренд: Danfoss Страницы: 16
Danfoss AK-PC 420 User Manual preview
AK-PC 420
Бренд: Danfoss Страницы: 20
Danfoss ADAP-KOOL AK-PC 781 User Manual preview
ADAP-KOOL AK-PC 781
Бренд: Danfoss Страницы: 14
Danfoss 4033 Installation And User Instructions Manual preview
4033
Бренд: Danfoss Страницы: 12
Danfoss vlt soft starter mcd 500 Operating Manual preview
vlt soft starter mcd 500
Бренд: Danfoss Страницы: 96
Daihan Scientific WHM-C10D Operation Manual preview
WHM-C10D
Бренд: Daihan Scientific Страницы: 11
Apricus Sentinel S4 Mounting, Connection, Operation preview
Sentinel S4
Бренд: Apricus Страницы: 32
Analog Devices Linear Technology ADI Power DC3017A Demo Manual preview
Linear Technology ADI Power DC3017A
Бренд: Analog Devices Страницы: 12
Renogy Rover 100A Manual preview
Rover 100A
Бренд: Renogy Страницы: 36
Parker ACR1505 Hardware Installation preview
ACR1505
Бренд: Parker Страницы: 64
Metek TWRF1 SCR Series Instruction, Operation And Maintenance Manual preview
TWRF1 SCR Series
Бренд: Metek Страницы: 36
Tyco DSC WT5500 Installation Instructions Manual preview
DSC WT5500
Бренд: Tyco Страницы: 32

Бренды по названию

Популярные бренды

Загрузить еще бренды