manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

RM0082

HS_USB 2.0 device

Doc ID 018672 Rev 1

463/844

23 

HS_USB 2.0 device

23.1 Overview

In addition to single independent USB 2.0 hosts, within its high-speed (HS) connection 
subsystem SPEAr300 provides a USB 2.0 Device which is fully compliant with the universal 
serial bus specification (version 2.0), and offering an interface to the industry-standard AHB 
bus.

Main features provided by the USB 2.0 device are listed:

●

A PHY interface implementing a USB 2.0 transceiver macrocell interface (UTMI) fully 
compliant with UTMI specification (version 1.05), to execute serialization and 
deserialization of transmissions over the USB line. 

●

Unidirectional/bidirectional 8-/16 bit UTMI data bus interfaces are supported.

●

A USB plug detect (UPD) which detects the connection of a device (detailed in 

Section 23.7

).

●

A USB device controller (UDC) which is connected to the AHB bus and generates the 
commands for the UTMI PHY. Hereafter the UDC along with AHB interface is referred 
to UDC-AHB subsystem. 

●

The UDC-AHB supports the 480 Mbps high-speed (HS) for USB 2.0, as well as the 12 
Mbps full-speed (FS) for USB 1.1. 

●

The UDC-AHB supports 16 physical endpoints (listed in 

Table 388

), and proper 

configurations to achieve logical endpoints.

●

Both DMA mode and slave-only mode supported (detailed in 

Section 23.4

).

●

In DMA mode, the UDC-AHB supports descriptor-based memory structures in 
application memory.

●

In both modes, an AHB slave is provided by UDC-AHB, acting as programming 
interface to access to memory-mapped control and status registers (CSRs).

●

An AHB master for data transfer to system memory, supporting 8, 16, and 32 bit wide 
data transactions on the AHB bus.

         

Table 388.

Endpoints assignment

Endpoint number

Endpoint direction

Transfer type

0

IN/OUT

Control.

1-3-5-7-9-11-13-15

IN

Software configurable to:

Bulk

Interrupt

Isochronous.

2-4-6-8-10-12-14

OUT

Software configurable to:

Bulk

Interrupt

Isochronous.

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

Canarm MC Series Installation Manual preview
MC Series
Бренд: Canarm Страницы: 3
Caen V793 Technical Information Manual preview
V793
Бренд: Caen Страницы: 20
Phoenix Contact 2297031 Manual preview
2297031
Бренд: Phoenix Contact Страницы: 56
EBS CPX200NB Installation And Programming Manual preview
CPX200NB
Бренд: EBS Страницы: 116
Daikin BRC1H62W Operation Handbook preview
BRC1H62W
Бренд: Daikin Страницы: 2
Leviton GreenMax DRC DRC07-ED0 Quick Start Manual preview
GreenMax DRC DRC07-ED0
Бренд: Leviton Страницы: 2
Congatec SMARC conga-SMX8-X Quick Start Manual preview
SMARC conga-SMX8-X
Бренд: Congatec Страницы: 8
MT-Propeller P-8S Series Operation And Installation Manual preview
P-8S Series
Бренд: MT-Propeller Страницы: 16
zeeltronic PDCI-NS1V User Manual preview
PDCI-NS1V
Бренд: zeeltronic Страницы: 15
M-system M8BS2-081 Instruction Manual preview
M8BS2-081
Бренд: M-system Страницы: 3
E+L RK 4004 Manual preview
RK 4004
Бренд: E+L Страницы: 62
Omicron BETA 9.2 Quick Start Manual preview
BETA 9.2
Бренд: Omicron Страницы: 17
Simplex RTL-TH DIGITAL Installation And Operating Instructions Manual preview
RTL-TH DIGITAL
Бренд: Simplex Страницы: 12
Aurora Scientific 315D Instruction Manual preview
315D
Бренд: Aurora Scientific Страницы: 21
Clare Controls CLIQ.host Installation Sheet preview
CLIQ.host
Бренд: Clare Controls Страницы: 3
Swegon TACTouch TAC5 Manual preview
TACTouch TAC5
Бренд: Swegon Страницы: 11
G-Scale Graphics RailBoss 4 Basic Operation And Installation Manual preview
RailBoss 4 Basic
Бренд: G-Scale Graphics Страницы: 22
Interactive Technologies CueServer 2 User Manual preview
CueServer 2
Бренд: Interactive Technologies Страницы: 431

Бренды по названию

Популярные бренды

Загрузить еще бренды