manualshive.com logo in svg

STMicroelectronics RM0365, Справочное руководство


Поделиться
Скачать
background image

General-purpose timers (TIM15/TIM16/TIM17)

RM0365

639/1080

DocID025202 Rev 7

As the preload registers are transferred to the shadow registers only when an update event 
occurs, before starting the counter, you have to initialize all the registers by setting the UG 
bit in the TIMx_EGR register.

OCx polarity is software programmable using the CCxP bit in the TIMx_CCER register. It 
can be programmed as active high or active low. OCx output is enabled by a combination of 
the CCxE, CCxNE, MOE, OSSI and OSSR bits (TIMx_CCER and TIMx_BDTR registers). 
Refer to the TIMx_CCER register description for more details.

In PWM mode (1 or 2), TIMx_CNT and TIMx_CCRx are always compared to determine 
whether TIMx_CCRx

≤

TIMx_CNT or TIMx_CNT

≤

TIMx_CCRx (depending on the direction 

of the counter). 

The TIM15/TIM16/TIM17 are capable of upcounting only. Refer to 

Upcounting mode on 

page 625

.

In the following example, we consider PWM mode 1. The reference PWM signal OCxREF is 
high as long as TIMx_CNT < TIMx_CCRx else it becomes low. If the compare value in 
TIMx_CCRx is greater than the auto-reload value (in TIMx_ARR) then OCxREF is held at 
‘1’. If the compare value is 0 then OCxRef is held at ‘0’. 

Figure 258

 shows some edge-

aligned PWM waveforms in an example where TIMx_ARR=8.

Figure 258. Edge-aligned PWM waveforms (ARR=8)

22.4.11 

Combined PWM mode (TIM15 only)

Combined PWM mode allows two edge or center-aligned PWM signals to be generated with 
programmable delay and phase shift between respective pulses. While the frequency is 
determined by the value of the TIMx_ARR register, the duty cycle and delay are determined 

069

&RXQWHUUHJLVWHU

µ¶

2&;5()

&&[,)

2&;5()

&&[,)

2&;5()

&&[,)

2&;5()

&&[,)

&&5[

&&5[

&&5[!

&&5[

µ¶

Содержание RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RM0365

LogLogic LX 1010 Quick Start Manual preview
LX 1010
Бренд: LogLogic Страницы: 30
Acces I/O products MPCIE-ICM232-2 Hardware Manual preview
MPCIE-ICM232-2
Бренд: Acces I/O products Страницы: 5
Enertronica Santerno SINUS H PROFInet User Manual preview
SINUS H PROFInet
Бренд: Enertronica Santerno Страницы: 34
Infoblox Trinzic 100 Installation Manual preview
Trinzic 100
Бренд: Infoblox Страницы: 13
Acromag APCe7012E-LF User Manual preview
APCe7012E-LF
Бренд: Acromag Страницы: 23
Top RAMS1000 User Manual preview
RAMS1000
Бренд: Top Страницы: 21
iesy Open Standard Module RPX30 EVA-MI V1 Quick Start Manual preview
Open Standard Module RPX30 EVA-MI V1
Бренд: iesy Страницы: 9
2N Telekomunikace ATEUS STARGATE User Manual preview
ATEUS STARGATE
Бренд: 2N Telekomunikace Страницы: 67
Xinje VH5 Series User Manual preview
VH5 Series
Бренд: Xinje Страницы: 76
Juniper WX 100 Quick Start Manual preview
WX 100
Бренд: Juniper Страницы: 6
Cypress Semiconductor CY7C027AV Specification Sheet preview
CY7C027AV
Бренд: Cypress Semiconductor Страницы: 18
Renesas RH850 Series User Manual preview
RH850 Series
Бренд: Renesas Страницы: 67
TEC Control WiDiCast User Manual preview
WiDiCast
Бренд: TEC Control Страницы: 4
ICP DAS USA WF-2572M User Manual preview
WF-2572M
Бренд: ICP DAS USA Страницы: 26
IBM 32R1860 - Nortel Layer 2/3 Copper GbE Switch... User Manual preview
32R1860 - Nortel Layer 2/3 Copper GbE Switch...
Бренд: IBM Страницы: 14
3Com 3CRWE737A - 11Mbps Airconnect Wireless Lan PC Card... Datasheet preview
3CRWE737A - 11Mbps Airconnect Wireless Lan PC Card...
Бренд: 3Com Страницы: 6
Advantech ARK-10 User Manual preview
ARK-10
Бренд: Advantech Страницы: 59
ICP DAS USA PEX-P8R8i Quick Start Manual preview
PEX-P8R8i
Бренд: ICP DAS USA Страницы: 9

Бренды по названию

Популярные бренды

Загрузить еще бренды