manualshive.com logo in svg

STMicroelectronics RM0365, Справочное руководство


Поделиться
Скачать
background image

DocID025202 Rev 7

174/1080

RM0365

System configuration controller (SYSCFG)

182

11.1.2 

SYSCFG external interrupt configuration register 1
(SYSCFG_EXTICR1)

Address offset: 0x08

Reset value: 0x0000 0000

         

Bit 11

TIM16_DMA_RMP:

 TIM16 DMA request remapping bit

This bit is set and cleared by software. It controls the remapping of TIM16 DMA request.

0: No remap (TIM16_CH1 and TIM16_UP DMA requests mapped on DMA1 channel 3)
1: Remap (TIM16_CH1 and TIM16_UP DMA requests mapped on DMA1 channel 6)

Bits 10:9 Reserved, must be kept at reset value.

Bit 8

ADC2_DMA_RMP:

 ADC2 DMA remapping bit (STM32F302xB/C/D/E devices only)

This bit is set and cleared by software. It controls the remapping of ADC24 DMA requests.

0: No remap (ADC24 DMA requests mapped on DMA2 channels 1 and 2)
1: Remap (ADC24 DMA requests mapped on DMA2 channels 3 and 4)

Bit 7

DAC1_TRIG_RMP:

 DAC trigger remap (when TSEL = 001) (STM32F302xB/C/D/E devices 

only)
This bit is set and cleared by software. It controls the mapping of the DAC trigger source.

0: No remap 
1: Remap (DAC trigger is TIM3_TRGO)

Bit 6

TIM1_ITR3_RMP:

 Timer 1 ITR3 selection

This bit is set and cleared by software. It controls the mapping of TIM1 ITR3.

0: No remap (TIM1_ITR3 = TIM4_TRGO in STM32F302xB/C/D/E devices)
1: Remap (TIM1_ITR3 = TIM17_OC)

Bits 5:3 Reserved, must be kept at reset value.

Bits 2:0

MEM_MODE:

 Memory mapping selection bits

This bit is set and cleared by software. It controls the memory internal mapping at address 
0x0000 0000. After reset these bits take on the memory mapping selected by BOOT0 pin and 
BOOT1 option bit.

0x0: Main Flash memory mapped at 0x0000 0000
001: System Flash memory mapped at 0x0000 0000
011: Embedded SRAM (on the D-Code bus) mapped at 0x0000 0000
1xx: FMC Bank (Only the first  two banks) (Available on STM32F302xD/E only).

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

Res.

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

EXTI3[3:0]

EXTI2[3:0]

EXTI1[3:0]

EXTI0[3:0]

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

Содержание RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RM0365

NEC N8104-128 Installation Manual preview
N8104-128
Бренд: NEC Страницы: 47
Datasat AP20 Installation And Operating Manual preview
AP20
Бренд: Datasat Страницы: 32
Lab.gruppen NLB 60E Operation Manual preview
NLB 60E
Бренд: Lab.gruppen Страницы: 35
Paradyne 8540 Installation Instructions Manual preview
8540
Бренд: Paradyne Страницы: 12
Rolls HR11C Owner'S Manual preview
HR11C
Бренд: Rolls Страницы: 2
hilscher CIFX 104 User Manual preview
CIFX 104
Бренд: hilscher Страницы: 154
Accom WSD/HDe Installation Procedure preview
WSD/HDe
Бренд: Accom Страницы: 15
TDK InvenSense RoboKit1 Hardware Reference Manual preview
InvenSense RoboKit1
Бренд: TDK Страницы: 13
TVT Digital TD-3316B4-16P-A1 Quick Start Manual preview
TD-3316B4-16P-A1
Бренд: TVT Digital Страницы: 2
Advantech ARK-1380 User Manual preview
ARK-1380
Бренд: Advantech Страницы: 50
ZALMAN Fatal1ty FS-V7 User Manual preview
Fatal1ty FS-V7
Бренд: ZALMAN Страницы: 9
Cypress Semiconductor CY7C1303BV25 Specification Sheet preview
CY7C1303BV25
Бренд: Cypress Semiconductor Страницы: 19
Inspired Energy ATA004N Operating Instructions preview
ATA004N
Бренд: Inspired Energy Страницы: 5
Pilz PNOZ mc3p Operating Instructions Manual preview
PNOZ mc3p
Бренд: Pilz Страницы: 12
Kontron ADA-SDVO-PEG16 User Manual preview
ADA-SDVO-PEG16
Бренд: Kontron Страницы: 14
Data Translation DT9835 Getting Started Manual preview
DT9835
Бренд: Data Translation Страницы: 62
Apposite Technologies Linktropy MINI-G User Manual preview
Linktropy MINI-G
Бренд: Apposite Technologies Страницы: 57
Corsair H100i Manual preview
H100i
Бренд: Corsair Страницы: 134

Бренды по названию

Популярные бренды

Загрузить еще бренды