STK Professional Audio VM-11S DRV, Руководство пользователя

Страница: 9 / 28

9
6a. High
The high frequency shelf control is set at 8kHz. You can
increase or attenuate frequencies 8kHz(and above)up to 15dB.
There is a detente in the 0 position indicating a flat response.
7a. Mid
The mid frequency is centered at 2.5 kHz. You can increase or
attenuate the midrange frequencies by as much 12dB. A
detente is provided in the 0 position indicating a flat response.
8a. Low
The low frequency shelf control is set at 80Hz. You can
increase or attenuate frequencies 80Hz(and below) up to 15dB.
A detente is provided in the 0 position indicating a flat
response.
9a. Bal
This control varies the amount of channel signal sent to either
the left or right channel of the stereo mixer.
FRONT PANEL MASTER SECTION
11. Aux In
Connect these jacks to the output jacks of an external effects
processor. If the effects processor has a stereo output, connect
it to the AUX IN L(MONO) and R jacks. If it has monaural
output, use the AUX IN L(MONO) jack. Signal input to these
jacks is sent to the ST bus.
12. Tape In
Use these jacks to connect a stereo device, such as a cassette
player or a CD player. The signals input to these jacks is sent
to the ST bus.
13. Rec Out
The ST bus signal before it has passed through the MASTER
control and graphic equalizer.
14. Monitor Out
The MONI bus signal which has passed through the MASTER
control and graphic equalizer.
15. Left/Main, Right/Mon Out
The Left/Main and Right/Mon output 1/4" connectors are the
final output for the master stereo mix and controlled by the
master left and Right level volume pots.
16. EFX Out
The input of an external effect such as a delay or echo can be
connected to this jack. The signal adjusted by the EFFECT
control of each channel will be sent to the EFFECT bus, its
level adjusted by the EFFECT OUT control, and output from
this jack.
17. Footswitch
The DSP Footswitch jack is a standard 1/4 ＂ size
accommodating a monaural ON/OFF Footswitch that
enables/disable the internal digital effects.
18. Mono/Subwoofer
This line level subwoofer output allows you to conveniently add
supplemental buss to your system. The signal is derived from summed
left+right master output or the master output and is routed through a
125Hz low pass filter
.
19. Aux In /Tape In Control
This control varies the amount of the signal from the Tape In
and Aux In mixed back to the main buss.
20. Aux / Tape to Mon Control
The Aux/Tape to Mon Control provides continuously variable
adjustment of the signal derived from the tape in jacks located
on the connector panel and sends that signal to the monitor
master control.
21. Main Amp Assign (L+R/Bridge, Stereo)
This slide switch select a main amp signal route depending on
the speakers connected to the speaker Left&Right or L+R
bridge jacks on the rear panel.
22. Master Monitor Control
This controls the overall signal level at the Monitor Line Out.
This setting is output to both the front and rear panel monitor
jacks and appears in the monitor bus signal.
23. Master Left/Main Bridge(Mono)
This control provides adjustment of signal to the left main
output connector, and serves as a volume control for the left
internal amplifier :
In Left+Right mode.
24. Master Right/Monitor
This control provides adjustment of signal to the right main
output connector, and serves as a volume control for the right
internal amplifier :
In Monitor mode.
25. DSP Switch
This push control activates/deactivates the DSP effects.
26. EFX To Mon
This master DSP EFX level control sent to Mon bus varies the
amount of overall combined signal of the independent
channels.
27. EFX To Main
This master DSP EFX level control sent to main bus varies the
amount of overall combined signal of the independent
channels.
Ⅳ Panel Descriptions
VM-11SDRV