15
MODEL: SOBF118 | PRODUCT CODE: 59117 | 10/2017
Other Useful Information
Cleaning and Maintenance
WARNING
Before cleaning the appliance, make sure it is switched off and disconnected from the power supply.
Failure to do so can result in electric shock or injury.
• Before cleaning: take out any drinks as well as the shelves.
• Wash the inside surfaces with a solution of lukewarm water (1L) and baking soda (2 tbsp). Use a soft, clean
cloth to wipe down the surfaces, then rinse with clean water and dry with a dry cloth. Do not use soap or
detergent for cleaning the cabinet. DO NOT allow the control panel, cables or plug to get wet.
NOTE:
Wring excess water out of the cloth when cleaning around the controls or electrical parts.
• Make sure to keep the door gasket (seal) clean to keep the unit running effi ciently.
• Wash the shelves and the outside of the cabinet with a mild detergent solution.
Wipe dry with a clean soft cloth.
• Dust or anything else blocking the vent may hinder the cooling effi ciency of the appliance.
Always keep the vent clean; vacuum it if necessary.
WARNING
Never clean the unit with an abrasive, acid, oil or solvent based cleaning agent. Never use fl ammable fl uids
or sprays for cleaning as the fumes from these substances can create a fi re hazard or explosion.
When You Are on Holidays
• Leave the beverage chiller operating during holidays of less than three weeks. If you are not going to use
the beverage chiller for longer periods, remove all items and unplug the power cord. Clean and dry the
interior thoroughly. To prevent odours and mould growth, leave the door open slightly, blocking it open
if necessary.
• To move the beverage chiller, take all items out of the appliance, securely tape down the shelves or remove
them and tape the door shut. Turn the levelling leg up to the base to avoid damage.
• Protect the outside of the beverage chiller with a blanket or similar soft material and make sure the
beverage chiller stays secure in the upright position during transportation.
Adjusting the Height and Leveling
• The appliance is equipped with adjustable feet, so that the height may be adjusted to
level the cabinet on uneven fl oor surfaces.
• We recommend that two people carry out this procedure.
• The height must be adjusted prior to building the appliance into the housing unit and
it should be set at such a height that the top panel of the appliance fi ts 5cm below
the kitchen worktop.
• Tilt the appliance approximately 60° to allow access to the adjustable feet.
• Take care to ensure the cabinet is supported at all times.
• Twist the foot into a suitable position to level the cabinet. (Fig. 5)
• Repeat these steps for the other adjustable feet.
IMPORTANT:
If the appliance is not level, then the door and door seal may be affected.
IMPORTANT:
Do not move the appliance when the feet are adjusted high.
.17.
Adjusting the height and leveling off your wine cabinet
o The appliance is equipped with adjustable feet, so that the height may
be adjusted to level the cabinet on uneven floor surfaces.
o We recommend that two people carry out this procedure.
o The height must be adjusted prior to building the appliance into the
housing unit and it should be set at such a height that the top panel of
the appliance fits exactly below the kitchen worktop.
o Tilt the appliance approximately 60° to allow access
to the adjustable feet.
o Take care to ensure the cabinet is supported at all
times.
o Twist the foot into a suitable position to level the
cabinet.
o Repeat these steps for the other adjustable feet.
IMPORTANT: If the appliance is not level, then the door and door seal may
be affected.
IMPORTANT: Do not move the appliance when the feet are adjusted high.
Installing The Handle
o Remove the door Gasket slightly to
expose the two screw holes.
o Fix the Handle by screwing the two
Handle Screws tightly, the Handle
Screws with Washers are pre-installed
inside the screw holes, pls.do not
unscrew the Handle Screws too much
in case the Washers fell off.
o Replace the Gasket.
Fig. 5
