background image

EN

 

77

 

 

 

 

 

 

 

 

 

 

 

 

 

0478 131 8365 C - EN

Message:

1000 – Rollover
Allowed inclination exceeded

Possible cause:

– Tilt sensor has detected a rollover

Remedy:

– Place robotic mower on its wheels, 

check for damage and confirm 
message with OK

Message:

1010 – iMOW® raised
Press OK to release

Possible cause:

– Robotic mower has been lifted by hood

Remedy:

– Check movement of hood and confirm 

message with OK

Message:

1030 – Hood fault
Check hood
Then press OK

Possible cause:

– No hood detected

Remedy:

– Check hood (movement, firm seating) 

and confirm the message with OK

Message:

1105 – Flap open
Operation aborted

Possible cause:

– Flap open during automatic operation
– Flap open during automatic edge 

following

Remedy:

– Close the flap (

Ö

15.2)

Message:

1120 – Hood blocked
Check hood
then press OK

Possible cause:

– Permanent collision detected
– Uneven areas around or underneath 

docking station floor plate

Remedy:

– Free robotic mower, remove obstacle or 

change routing of perimeter wire if 
necessary – then confirm message with 
OK

– Check movement of hood and confirm 

message with OK

– Level out uneven areas and confirm 

message with OK (

Ö

9.1)

Message:

1125 – Remove obstacle
Check wire routing

Possible cause:

– Perimeter wire routed inaccurately

Remedy:

– Check routing of the perimeter wire, 

check clearances using the 
iMOW® Ruler (

Ö

12.5)

Message:

1126 – Cancel teach-in
Teach-in failed
Remove obstacle

Possible cause:

– Obstacle in the area of the perimeter 

wire

– Hood has been lifted

– Wire routing incorrect

Remedy:

– Free robotic mower, remove obstacle or 

change routing of perimeter wire if 
necessary

– Check movement of the hood
– Level out uneven areas
– Confirm the message with OK
– Restart teach-in run if necessary

Message:

1127 – Cancel teach-in
Teach-in failed

Possible cause:

– STOP button was pressed
– Allowed inclination exceeded
– Delete/save internal map of the mowing 

area failed

– Docking was not successful

Remedy:

– Confirm the message with OK
– Restart teach-in run if necessary

Message:

1128 – Direct drive home
Drive home on the wire aborted

Possible cause:

– Direct drive home could not be 

successfully completed

Remedy:

– No action required, confirm message 

with OK if necessary

– Contact your STIHL specialist dealer if 

the problem persists

Содержание RMI 522 C

































































































Отзывы: