Stihl RMI 522 C, Инструкция по эксплуатации

Страница: 64 / 96

0478 131 8365 C - EN
62
14.3 Active times
In the mow plan type "Standard", the
robotic mower mows throughout the entire
active time, only interrupted by charging
operations.
In the mow plan type "Dynamic", the
robotic mower is allowed to leave the
docking station at any time during the
active times and mow the lawn. During
these times,
mowing operations ,
charging operations and rest periods
take place. The robotic mower
automatically distributes the mowing and
charging operations between the available
time windows.
During installation, active times are
automatically distributed over the entire
week. Time reserves are taken into
account – this ensures perfect lawn care,
even if individual mowing operations
cannot take place, (e.g. due to rain).
14.4 Mowing duration
The mowing duration specifies how many
hours per week the lawn is to be mown. It
can be extended or reduced. (
Ö 11.7)
The mowing duration corresponds to the
time during which the robotic mower mows
the lawn. Times during which the battery is
charged are not part of the mowing
duration.
During initial installation, the robotic
mower automatically calculates the
mowing duration based on the specified
size of the mowing area. This reference
value is based on a normal lawn under dry
conditions.
Mowing performance:
For 100 m
2
, the robotic mower needs on
average 100 minutes.
14.5 Home area
The robotic mower identifies its location
using the built-in GPS receiver. During
each edge following run to check the
correct wire routing (
Ö 9.12) and when
learning the starting points ( Ö 11.14), the
robotic mower stores the coordinates of
the most westerly, easterly, southerly and
northerly point.
This area is defined as the home area and
the robotic mower can be used here. The
coordinates are updated each time edge
following is repeated.
When GPS protection is activated, the
owner of the machine is notified if the
machine is operated outside the home
area. The PIN code is also requested on
the robotic mower display.
15.1 Preparation
● Install the docking station ( Ö 9.8)
● Route ( Ö 9.9) and connect ( Ö 9.10) the
perimeter wire
● Remove foreign bodies (e.g. toys,
tools) from the mowing area
● Charge the battery ( Ö 15.7)
● Set the time and date ( Ö 11.10)
● Check the mowing plan and adapt if
necessary – in particular it must be
ensured that third parties keep away
from the danger area during active
times. (
Ö 11.7)
15.2 Flap
The robotic mower is equipped with a flap
which protects the display from the
weather and from inadvertent operation. If
the flap is opened during use of the robotic
mower, operation is stopped and the
mowing blade and robotic mower come to
a standstill.
During the active times, third
parties must keep out of the danger
area. The active times should be
adapted accordingly.
Moreover, the applicable local
regulations on the use of robotic
mowers as well as the information
in the "For your safety"
section (
Ö 6.1) must be observed
and the active times changed
accordingly in the "Mowing plan"
menu as required. (
Ö 11.7)
In particular, you should check the
times of the day and night at which
it is permissible to use the machine
with the responsible authorities.
15. Operating the machine
An installation assistant is available
for
initial installation . ( Ö 9.)
The robotic mower should be
charged and operated at an
ambient temperature b5°C
and +40°C.
Cut very high grass short using a
conventional lawn mower prior to
use of the robotic mower
(e.g. following a lengthy break).