Stihl FS 40 Скачать руководство пользователя

Страница: 66 / 82

Series 4144 Components FC, FS, KM

Drive Tube

9.1

Removing and Installing

The drive tube can be removed from
the machine without dismantling
other parts.

Machines with loop handle

Take out the screw (1) and
loosen the screws (arrows).

– Pull out the drive tube (2).

– Check the drive tube and repair

or replace if necessary,

9.1

Machines with bike handle

Loosen the screw (arrow).

– Pull off the control handle (1).

545RA001 TG

545RA073 TG

Take out the screw (1) and
loosen the screws (arrows).

– Pull the drive tube (2) out of the

engine housing.

– Check the drive tube and repair

or replace if necessary,

9.1

If a new drive tube is installed, the
other parts and components must
be transferred from the old drive
tube.

Installing

– Degrease the clamp area with a

little standard solvent-based
degreasant containing no
chlorinated or halogenated
hydrocarbons,

Machines with loop handle

Position the drive tube (1) so that
the holes are in alignment.

545RA000 TG

545RA002 TG

– Push home the drive tube (1) as

far as stop, turn the drive shaft to
and fro until the square end of the
drive shaft engages the square
recess in the clutch drum.

Turn the drive tube (1) until the
holes (arrow) in the drive tube
and engine housing line up.

– Insert and tighten down the screw

– turn the drive tube to and fro
until the screw slips through the
hole – the drive tube is only
located and not clamped in
position at this stage.

Tighten down the screws
(arrows) firmly.

545RA003 TG

545RA004 TG

Содержание FS 40



















































































Результаты поиска

Содержание FS 40

Отзывы:

Похожие инструкции для FS 40

Бренды по названию

Популярные бренды

Stihl FS 40, Руководство по обслуживанию

Результаты поиска

Содержание FS 40

Отзывы:

Похожие инструкции для FS 40

Бренды по названию

Популярные бренды