Stihl E 140 Скачать руководство пользователя

Страница: 20 / 25

- Remove the switch lever -

see 8.1.

- Remove the rotor -

see 5.2.

•

Unhook brake rod from brake
lever.

•

Detach the springs.

•

Remove the brake band fasten-
ing screw.

•

Pry the brake band out of the
gear housing.

•

Unhook brake band from brake
lever.

- Inspect brake band and fit new

one if:

- there are definite signs of wear

(large areas of inside diameter
and/or parts of outside diameter)
and

- band thickness is less than 0.6

mm (0.025").

Important:

The brake band must

must not be thinner

at any

point.

- If the brake band is still service-

able, clean and roughen its
entire friction surface (inside of
brake band) with emery paper or
cloth (grain size approx. 120

m).

•

Pry the carrier and articulated
lever off the bearing pin and lift
them away together.

- Pull the articulated lever out off

the carrier.

•

Remove the flat spring.

- Inspect all parts. Always replace

damaged parts.

- Clean housing recess for chain

brake mechanism.

100RA091

100RA092

100RA093

100RA094

100RA095

100RA097

100RA098

Содержание E 140


























Результаты поиска

Содержание E 140

Отзывы:

Похожие инструкции для E 140

Бренды по названию

Популярные бренды

Stihl E 140, Руководство по обслуживанию

Результаты поиска

Содержание E 140

Отзывы:

Похожие инструкции для E 140

Бренды по названию

Популярные бренды