STIEBEL ELTRON WPL 09 ICS classic Скачать руководство пользователя страница 7

Страница: 7 / 44

INSTALLATION

Safety

www.stiebel-eltron.com

WPL ICS classic | WPL IKCS classic |

INSTALLATION

7. Safety

Only a qualified contractor should carry out installation, commis-

sioning, maintenance and repair of the appliance.

7.1 General safety instructions

We guarantee trouble-free function and operational reliability only

if original accessories and spare parts intended for the appliance

are used.

7.2 Instructions, standards and regulations

Note

Observe all applicable national and regional regulations

and instructions.

The tested appliance conforms to IEC 61000-3-12.

7.3 Operation of the appliance in buildings with

combustion equipment

As the appliance can produce negative pressure in the installa-

tion room, we recommend using a tightly sealing door between

the installation room and the living space containing combustion

equipment.
If, due to its use, the installation room is connected to the extract

air system, you must also make special arrangements for a supply

air vent in the installation room, to prevent any further increase in

the negative pressure in this room. The negative pressure created

by the appliance in the installation room is heavily influenced by

the pressure drop in the outdoor air line. For this reason, the

outdoor air line in particular should be as short as possible.

8. Appliance description

At +8 °C condenser temperature, the integral frost protection cir-

cuit automatically starts the heating circulation pump in the heat

pump circuit, thereby ensuring circulation in all water carrying

sections.
The heat pump starts automatically when the temperature in the

heat pump circuit drops below +5 °C.

8.1 Standard delivery

- Base unit

- Outside temperature sensor AF PT

- 2x Immersion/contact sensor TAF PT

- Transport aid

- 4x Sliding block

WPL 09 IKCS classic | WPL 17 IKCS classic

- 2 dummy covers

8.2 Required accessories

If installing a new appliance

- 2x air routing accessory LSWP 315 AWG Set
The air routing accessory is available in different lengths (0.7-4 m),

in silver (SR) or grey (GL), and as a version for light wells (L):

- LSWP 315-0.7 S AWG SR Set

- LSWP 315-2 S AWG SR Set

- LSWP 315-3 S AWG SR Set

- LSWP 315-4 S AWG SR set

- LSWP 315-0.7 S AWG GL Set

- LSWP 315-2 S AWG GL set

- LSWP 315-3 S AWG GL Set

- LSWP 315-4 S AWG GL Set

- LSWP 315-0.7 S AWG L Set

- LSWP 315-2 S AWG L Set

- LSWP 315-3 S AWG L set

- LSWP 315-4 S AWG L Set

If using existing air hoses and wall outlets AWG 315

- 2x quick-fit adaptor ZSA 315

8.3 Additional accessories

- Water softening fitting HZEA

- Condensate pump PK 10

- Internet Service Gateway ISG

- Remote control FET

- FE7 remote control

- TAF PT immersion/contact sensor

9. Preparation

9.1 Sound emissions

Take the following information into account when selecting the

installation location.

Note

The appliance is designed for indoor installation, except

in damp areas.

Note

For details regarding the sound power level, see chapter

"Specification / Data table".

- Never site the appliance on joist floors.

Ensure that the entire appliance frame is in full contact

with the substrate. Uneven substrates can increase sound

emissions.

Never install the appliance directly below or next to a living

room or bedroom.

Ensure that the air intake and discharge apertures in external

walls are not directed towards the neighbouring windows of

living rooms or bedrooms.

Содержание WPL 09 ICS classic













































Результаты поиска

Содержание WPL 09 ICS classic

Отзывы:

Похожие инструкции для WPL 09 ICS classic

Бренды по названию

Популярные бренды

STIEBEL ELTRON WPL 09 ICS classic, Эксплуатация и установка

Результаты поиска

Содержание WPL 09 ICS classic

Отзывы:

Похожие инструкции для WPL 09 ICS classic

Бренды по названию

Популярные бренды