manualshive.com logo in svg

STIEBEL ELTRON MINI-E 2-1, Руководство по эксплуатации и установке, Страница: 14 / 23

Поделиться
Скачать
STIEBEL ELTRON MINI-E 2-1 Скачать руководство пользователя страница 14

14

 |  MINI

™

-E SERIES TANKLESS ELECTRIC WATER HEATERS 

WWW.STIEBEL-ELTRON-USA.COM

SHUTTING DOWN

 Setting the maximum temperature 

 Factory setting:  100°F / 38°C

86°F / 30°C

100°F / 38°C

122°F / 50°C

D000004

20

35

 

  Do not adjust the temperature unless the power supply has 
been deactivated/disconnected.

f

 Using a fl at screwdriver, set the potentiometer to the maximum 
required temperature. 

f

 Re-fi t the appliance cover. 

12.  

Shutting down 

f

Turn off the circuit breaker connected to the appliance.

f

 Drain the appliance (See , “Draining the appliance”, pg. 16). 

13.  

Troubleshooting 

 Problem  

Cause  

Remedy 

 The appliance will not 
start despite the tap 
being fully open. 

No power to the appliance Check the fuses/circuit 

breaker.

 The flow rate is too low. 

 Increase the flow rate. 

 The filter screen in the 
cold water line is blocked.
 

 Clean the filter screen after 
shutting off the cold water 
inlet line. 

 The heater is faulty.

 

 Check the resistance of the 
heating system and replace 
the appliance if required.  
Contact Stiebel Eltron for 
additional troubleshooting

 The safety pressure cutout 
has activated. 

 Remedy the cause of the 
fault.   Isolate the appliance 
from the power supply and 
depressurize the water line.  
 Reset the safety pressure 
cutout. 

Содержание MINI-E 2-1
























Отзывы:

Нет отзывов