STEYR MOTORS MO114K33 Скачать руководство пользователя страница 24

Страница: 24 / 134

Before Starting

Familiarize yourself with the handling of the boat, in particular how to use transmission, and then proceed as follows:

Check the bilge for excessive water accumulation. Always keep the bilge clean and dry. Never allow the water

level in the engine compartment to exceed the bottom of the oil pan. If water accumulation is unavoidable,

install a bilge pump with an automatic control switch.

NOTE:

The water level in the boat’s engine compartment will increase when the boat is operated at

a high incline before planing speed is reached. Excessive water accumulation in the engine

compartment/bilge may cause engine failures.

Open the raw water intake valve.

NOTE:

Operate the engine only while the raw water supply is assured or the cooling system is

equipped with a flushing device. The raw water pump will be damaged and/or the engine will

overheat if operated without cooling water.

Open the fuel stop valve.

NOTE:

Only start the engine when a bubble-free fuel supply is guaranteed. Prior to first start-up of

the engine (after installation, after storage etc.), purge the fuel system by “ignition ON” for

6 x 10 sec.

If the suction height of the fuel-pump is more than 0.5 m, the fuel supply line must be filled

before first start-up of the engine.

Check the operating levels of:

* coolant

* oil

* hydraulic oil

* transmission oil

* fuel

Control of electric system:

* Charge and charge state of battery.

Содержание MO114K33







































































































































Результаты поиска

Содержание MO114K33

Отзывы:

STEYR MOTORS MO114K33, Руководство по эксплуатации, техническому обслуживанию и гарантии, Страница: 24 / 134

Результаты поиска

Содержание MO114K33

Отзывы: