STEYR MOTORS MO114K33 Скачать руководство пользователя страница 17

Страница: 17 / 134

Repair Service

All repair works on your

STEYR MOTORS GmbH marine engine

should be carried out by a licensed STEYR MO-

TORS GmbH Marine Dealer with his professional knowledge, trained staff and special-purpose tools to solve all oc-

curing problems. Preferably, all work on your

STEYR MOTORS GmbH marine engine

should be carried out by the

STEYR MOTORS GmbH Marine Dealer that sold the equipment to you - he knows you and the equipment.

If problems occur during a trip, bring your

engine

to the next

STEYR MOTORS GmbH

Marine Dealer

Information

on Dealers and Distributors can be found at the end of this manual.

Replacement Parts

Your

STEYR MOTORS GmbH Marine Engine

was designed to operate in a marine environment use STEYR MO-

TORS GmbH original replacement parts.

Before Casting Off

Check the weather report, wind and water conditions. Tell someone where you are going to and when you expect to

arrive or return.

Recommended Minimum

On-Board Tools

Screwdriver Set

lubrication oil spray

Metric Socket Set

12-volt pilot lamp

Metric Allen Key Set

flashlight

Metric Spanner Set

insulating tape

long nose pliers

sharp knife

Recommended Minimum

On-Board Spare Parts

propeller and small parts for propeller mounting

fuses

fuel filter ( pre- & finefilter)

bulbs

impeller for raw water pump

sealing compound

These lists represent a suggested

MINIMUM

and are not intended to cover all boats or possible boating conditions.

Содержание MO114K33







































































































































Результаты поиска

Содержание MO114K33

Отзывы:

STEYR MOTORS MO114K33, Руководство по эксплуатации, техническому обслуживанию и гарантии, Страница: 17 / 134

Результаты поиска

Содержание MO114K33

Отзывы: