Stevens AeroModel microHawk Скачать руководство пользователя страница 3

Страница: 3 / 12

Wood Bundle

☐

Illustrated build instruction manual

☐

Laser-cut wood, 4 sheets

☐

1 Carbon

ber tail boom (5 in. length)

Hardware Bag

☐

1 Plywood F3 fuselage joiner

☐

1 Length of heat-shrink tubing, 3/8 in. diameter

☐

Modeling clay, ballast, 12 grams

Introduction

The Stevens AeroModel

micro

Hawk

is a simple, all-sheet, entry level motor glider – designed to be powered by

popular 8.5 mm coreless motors and a 10 farad capacitor “fuel” system. When properly assembled and

ight

trimmed, a single charge from a 3 volt source provides exciting powered

ights of up to one minute in duration.

Kit Inventory

Required Electronics for Powered Flight

Available directly from stevensaero.com

☐

10F Capacitor-Power Kit (SAP-CP/PK01)

☐

Battery and motor connector (SAUMEXT/3)

☐

Coreless motor (recovered from (PKZ3616 or PKZ3624)

☐

Propeller, GWS HD 2.5 x 0.8 or GWS HD 2.5 x 1.0

☐

3.7V 160mAh LiPo battery with suitable charger

Содержание microHawk













Результаты поиска

Содержание microHawk

Отзывы:

Похожие инструкции для microHawk

Бренды по названию

Популярные бренды

Stevens AeroModel microHawk, Инструкция по эксплуатации

Результаты поиска

Содержание microHawk

Отзывы:

Похожие инструкции для microHawk

Бренды по названию

Популярные бренды