background image

WARRANTY

Stevens AeroModel guarantees this kit to be free from defects in both material and workmanship at the 

date of purchase.  This warranty does not cover any component parts damaged by use or modification.   

In no case shall Stevens AeroModel’s liability exceed the original cost of the purchased kit.  Further, 

Stevens AeroModel reserves the right to change or modify this warranty without notice.

LIABILITY RELEASE

In that Stevens AeroModel has no control over the final assembly or material used for final assembly, 

no liability shall be assumed nor accepted for any damage resulting from use by the user.  By the act of 

using the user-assembled product, the user accepts all resulting liability.

If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is 

advised to return this kit immediately in new and unused condition to the place of purchase.

THIS PRODUCT IS NOT INTENDED FOR CHILDREN 12 YEARS OF AGE OR YOUNGER.

WARNING:

  This product may contain chemicals known to the State of California to cause cancer and 

or birth defects or other reproductive harm.

PRODUCT SUPPORT

This product has been engineered to function properly and perform as advertised, with the suggested 

power system and supporting electronics as outlined within this product manual.  Product support 

cannot be provided, nor can Stevens AeroModel assist in determining the suitability or use of 

electronics, hardware, or power systems not explicitly recommended by Stevens AeroModel.

For product assembly support, replacement parts, hardware, and electronics to complete this model, 

please contact Stevens AeroModel at 

www.stevensaero.com

.

Stevens AeroModel

26405 Judge Orr Rd. Colorado Springs, CO 80808 USA

719-387-4187 

www.stevensaero.com

Build Instructions                                                                                                             

scimon 30 V2 Build Instructions.  © 2014 Stevens AeroModel all rights reserved.

!

Page 2

Содержание Scimon 30

















Отзывы: