16
17
CX-1P
2.1. ENABLE OR DISABLE PERIODIC TRANSMISSION (ONLY CX-1P)
Aft er use, it is recommended that the periodic transmission be disabled to extend
CR2032
batt ery life
(It is recommended that the batt ery be replaced every 4 months)
.
When the igniti on is turned on, the alarm will give 1 beep if the control batt ery is low.
The CX-1P control comes
from the factory with the
presence transmission
DISABLED. Before use,
make sure the presence
transmission is ENABLED. If
it is disabled, the lock cycle
will begin.
PROGRAMMING CONTROLS
3
REMOTE CONTROL FUNCTIONS
4
Conventi onal Control:
Acti vates and deacti vates the alarm, with or without sound
signaling, commands auxiliary output (window automati on, trunk opening), panic/
rescue functi on, ultrasonic locator and shutdown. If the alarm control panel trips by
the presence control, conventi onal control will not be able to unlock the vehicle.
5.1. TRIGGERED ALARM
When the alarm is triggered, the siren and blinkers are acti vated and the vehicle
immediately goes into lockdown. The alarm sounds for 1 minute. The alarm then
waits for 30 seconds and automati cally rearms. Aft er the same sensor (igniti on,
ultrasound, door/hood, ba� ery cut and ultrasonic defect) sets off the alarm 10 ti mes,
that sensor is ignored unti l the alarm is acti vated again. This prevents faulty sensors
from disturbing people and draining your vehicle’s ba� ery.
6.1.
ANTI-THEFT THROUGH THE DOOR
If the door is opened and closed when the igniti on is on, the anti -theft functi on is
acti vated
(if functi on 6 of the programming table is enabled)
. If you do not press the
MASTER BUTTON
within 1min 20sec, the alarm will beep for 10 seconds and then
enter the lock cycle.entra no ciclo de bloqueio.
6.2. ANTI-THEFT BY IGNITION
Each ti me the igniti on is turned on, the anti -theft functi on is acti vated
(if functi on 7
of the programming table is enabled)
. If the
MASTER BUTTON
is not pressed within
1min 20sec, the alarm will beep for 10 seconds and then enter the lock cycle. The
MASTER BUTTON
can be pressed (up to 15 seconds) before the igniti on is turned on
to deacti vate this anti -theft functi on.
6.3. ANTI-THEFT BY PRESENCE
To acti vate the presence functi on, program the presence control
(see secti on 3)
.
When the igniti on is on, if the control panel does not receive the presence control’s
transmission in 2min and 40sec, the alarm will beep for 10sec and then enter the
progressive lock cycle. To acti vate and deacti vate periodic transmission:
Press and
hold then press the control LED will go out and blink 1 ti me for acti vated
periodic transmission or 2 ti mes for deacti vated periodic transmission.
5.2. LOCK OR UNLOCK
Allows you to confi gure two locking/unlocking ti mes:
0.8 second
or
2.5 second
pulse.
It can be used to control the original or central locks.
Some types of locks require a
current greater than 200 mA, requiring the installati on of an external relay.
5.3. AUTOMATIC LOCK (AUTO-LOCK)
This feature can be confi gured in functi on 3 (enable auto-lock). If enabled, the doors
lock automati cally 10 seconds aft er the igniti on is turned on and unlock immediately
aft er the igniti on is turned off . If the door/hood is or is open for 10 seconds, auto-lock
will not kick in.
5.4. EXPANSION
The negati ve glass pulse output (green / black wire) allows the acti vati on of the lift ing
of the original glass of diff erent vehicle models or using universal glass lift stati ons,
according to the opti ons in
item 5 of the confi gurati on table
.
Glass panes and
modules are not included in the alarm kit.
5.5. AUXILIARY OUTPUT
This output allows you to control convenience opti ons through the remote control,
such as opening windows or the trunk. To do this, press the bu� on on the remote
control and within 2 second the bu� on . Auxiliary output will remain negati ve as
long as the bu� on is held.
ALARM FUNCTIONS
INTEGRATED ANTI-THEFT SYSTEM
5
6
HOLD
THEN PRESS ...
...unti l the led turns off and
fl ash
1 ti me (ENABLE)
.
...unti l the led turns off and
fl ash
2 ti mes (DISABLE)
.
If the control is already programmed the siren will emit 1 beep. Each ti me a new
control is programmed to the control panel the memory is cleared. Therefore all
existi ng controls must be reprogrammed with the new one or they will not work.
TURN ON
IGNITION
PRESS THE MASTER BUTTON
UNTIL THE SIREN
BEEPS
TURN OFF
IGNITION
EMITS 3 BEEPS FOR EACH
PROGRAMMED CONTROL
PRESS
AND TOGETHER
