Steris P920011-649 Скачать руководство пользователя страница 73

Страница: 73 / 168

4-28

920011-649

Operator Manual

Processing Instructions

�

If optional Automated Leak Test Assembly is present;

�

Appropriate leak test hose is connected to each endoscope

leak test port (see

ECTION

4.4.1, P

REPARATION

);

�

Quick connect extremity of each leak test hose is connected

to appropriate flexible connection (see

ECTION

4.4.1,

REPARATION

);

�

Pressure is relieved from endoscope(s) (see

ECTION

4.4.1,

REPARATION

);

�

Reliance dry chemistry

container's expiration date is valid,

container is placed in Reliance CDS and the latch is closed on

the Reliance CDS (see

);

�

STERIS chemical indicator

bottle's expiration date is valid and

chemical indicator strip is placed in the clip on control handle

boot "A" (see

If all previous items are satisfactory, proceed with

4.8 Processing Cycle

There may be up to four cycle options to choose from depending if

WASHING SELECT option is set to YES or NO in Supervisor mode:

•

SINGLE endoscope processing cycle

with washing phase

, to

process one endoscope (one endoscope is placed in control

handle boot "A") through washing and high level disinfection

phases.

•

SINGLE endoscope processing cycle without washing phase

to process one endoscope (one endoscope is placed in control

handle boot "A") through a high level disinfection phase only.

•

DOUBLE endoscope processing cycle

with washing phase

to process two endoscopes (one endoscope is placed in control

handle boot "A" and one in control handle boot "B") through

washing and high level disinfection phases.

•

DOUBLE endoscope processing cycle

without washing

phase

, to process two endoscopes (one endoscope is placed in

control handle boot "A" and one in control handle boot "B")

through a high level disinfection phase only.

Total nominal cycle time with a washing phase is approximately

42 minutes. Cycle time depends on cycle settings entered in

Supervisor mode. Temperature, pressure and quality of building

water supply can also influence cycle time. Processing cycle

proceeds through cycle phases as described in

Table 5-1

Cycle

Description Chart

NOTE:

If an error message is displayed at any time during cycle, refer

ECTION

7, T

ROUBLESHOOTING

, for possible causes and solutions.

WARNING – INEFFECTIVE

PROCESS HAZARD: Using
washing phase of the cycle
does

not

replace

the

requirement

for

manual

cleaning.

Содержание P920011-649









































































































































































Результаты поиска

Содержание P920011-649

Отзывы:

Похожие инструкции для P920011-649

Бренды по названию

Популярные бренды

Steris P920011-649, Руководство оператора

Результаты поиска

Содержание P920011-649

Отзывы:

Похожие инструкции для P920011-649

Бренды по названию

Популярные бренды