Steris P920011-649 Скачать руководство пользователя страница 68

Страница: 68 / 168

4-23

Processing Instructions

Operator Manual

920011-649

4.4.6 Self-Diagnostic

The leak test self-diagnostic is available to the user and is to be

performed without any endoscope to verify the integrity of the

system. The leak test self-diagnostic lasts approximately 90

seconds. Leak test self-diagnostic can be performed with either the

door opened or closed.
Performing such a test without any hose assembly connected in the

processor allows the verification of the system.
To proceed with leak test self-diagnostic without any hose assembly

connected, go directly to

Step 5

Running the same test with the hose assembly connected and using

the plug provided on the other extremity allows verification of the

hose assembly. See

ECTION

4.4.1, P

REPARATION

for details on how

to connect hose assembly and see

To run leak test self-diagnostic using a hose plug on hose assembly,

proceed as follows:
1. Select appropriate leak test hose (see

ECTION

4.4.1,

REPARATION

and Figure 4-16 for details).

2. Connect quick connect extremity of leak test hose(s) to flexible

connection(s) labeled 1 and/or 2 (see

ECTION

4.4.1,

REPARATION

for details).

3. Select appropriate hose plug.

For example, hose plugs are identified "O" for Olympus

endoscopes, "P" for Pentax

endoscopes or "F" for Fujifilm

endoscopes(see Figure 4-21).

4. Connect hose plug to leak test hose other extremity.

NOTE:

Hose plug must remain in place on the extremity of the

leak test hose for the duration of the leak test self-diagnostic.

CAUTION – POSSIBLE EQUIPMENT

DAMAGE:

Remove

any

automated leak test hoses
present

endoscope

processing support before
performing a D-SHORT or a D-
LONG cycle. Performing a
decontamination

cycle

(D-

SHORT and D-LONG) with
automated leak test hose
assemblies

present

may

cause water to enter hoses.
Inspect

leak

test

hose

assemblies  for  presence  of
water  prior  to  processing  a
cycle.  Water  in  tubing  may
cause damage to endoscopes.

REF: 920-502-707

Figure 4-21. Automated Leak Test Hose Assembly

Plug (Olympus Shown)

Содержание P920011-649









































































































































































Результаты поиска

Содержание P920011-649

Отзывы:

Похожие инструкции для P920011-649

Бренды по названию

Популярные бренды

Steris P920011-649, Руководство оператора

Результаты поиска

Содержание P920011-649

Отзывы:

Похожие инструкции для P920011-649

Бренды по названию

Популярные бренды