Steris P920011-649 Скачать руководство пользователя страница 61

Страница: 61 / 168

4-16

920011-649

Operator Manual

Processing Instructions

Following the loading in the endoscope processing support, connect

leak test hoses 1 and/or 2 to endoscope(s) as follows:
1. Identify endoscope(s) manufacturer.
2. Select appropriate leak test hose(s).

For example, leak test hoses are identified "O" for use with

Olympus

endoscopes, "P" for use with Pentax

endoscopes or

"F" for use with Fujifilm

endoscopes (see Figure 4-16).

3. Slightly shake chamber flexible connections which are intended

to be used so any water droplets, remaining from preceding

cycle, do not get trapped when connecting leak test hoses.

4. To connect quick connect extremity of leak test hose(s) to

flexible connection(s) labeled 1 and/or 2, proceed as follows:

a. With one hand, hold quick connect extremity of leak test

hose (see Figure 4-17).

b. With other hand, press flexible connection into quick

connect. Quick connect locking sleeve moves forward and

locks automatically (see Figure 4-17).

IMPORTANT: Only endoscopes with a leak test port on the
light guide cable can be leak tested.

5. Connect other extremity of leak test hose(s) to endoscope leak

test port(s) (see Figure 4-18).

6. Insert Reliance dry chemistry container and STERIS

chemical indicator strip in endoscope processing support

(see

and

for details).

CAUTION – POSSIBLE EQUIPMENT

DAMAGE:

Remove

any

automated leak test hoses
present

endoscope

processing

support

before

performing a D-SHORT or a D-
LONG cycle. Performing a
decontamination

cycle

(D-

SHORT and D-LONG) with
automated

leak

test

hose

assemblies present may cause
water  to  enter  hoses.  Inspect
leak  test  hose  assemblies  for
presence  of  water  prior  to
processing  a  cycle.  Water  in
tubing  may  cause  damage  to
endoscopes.

Figure 4-16. Automated Leak Test Hose Assembly

(Fujifilm Shown)

Содержание P920011-649









































































































































































Результаты поиска

Содержание P920011-649

Отзывы:

Steris P920011-649, Руководство оператора, Страница: 61 / 168

Результаты поиска

Содержание P920011-649

Отзывы: