background image

 

 

 

To remove the rudder from the boat, you will need to loosen or remove the steering line from the rudder 
yoke and then rotate the rudder towards the bow until it is almost parallel with the hull.  At this point you 
will lift up to remove it from the rudder post tube.  When replacing the rudder, you will start with the 
stern end of the rudder facing the bow and push it fully into the hole and then twist it back to the normal 
position.  Simply pull up on the rudder to see if it is locked in place – if not, try again. For more 
information on the Smart Track Rudders, please visit our website for the Smart Track Manual.   

  

  

 

 

For removing the rudder blade from the steering housing, you want the rudder to be deployed.  Simply 
remove the pin from the side of the rudder and then pull out the locking plug.  Then pull the knot from 
the rudder blade to complete removal. 

 

To replace the rudder blade, you will put the knot into the hole and run the retraction line around the 
bottom of the rudder blade rope guide.  Then insert the rudder into the housing vertically in the deployed 
position.  Then simply insert the plastic locking knob through the housing and rudder blade and insert the 
pin to lock in place.  

  

  

 

 

Rudder Alignment:

 When changing the angle of your foot pedals or installing new steering line, make 

sure to check the alignment of your rudder.  Ideally, a helper can hold the rudder straight, while you 
tighten the steering line forward of the foot-pedals while making sure both pedals are at the same angle.

 

Weed Guard: 

 

Weed guards help deflect any debris from accumulating on 
the rudder of your boat.  Typically, debris will travel along 
the hull and get stuck under the rudder or on the leading 
edge, which will reduce your ability to steer as well as 
greatly decreasing your hull speed. 

 

The weed guard should be placed 2 mm in front of the 
rudder for adequate protection.  We recommend using a 
silicone adhesive which is semi permanent.  You will want to be sure that the hull is clean and dry before 
application and follow the directions for recommended drying time. 

Содержание Surf Skis












Отзывы: