Steinbach Speedcleaner RX5, Инструкция по эксплуатации

Страница: 9 / 60

Speedcleaner APPcontrol | 2017_V1 Page 9 of 60
EN
Attention
：
“
▶
”&“
◀
”need to be pressed constantly
.
Warning
Caution: Before removing the cleaner from
the pool, make sure that the electricity is fully
switched off.
Preparation
Care and maintenance
The cleaner turns itself off automatically after a cleaning cycle. Unplug
the mains cable, gently pull the cable, and lift the cleaner out of the
water using the ring on the clamp nut.
Caution:
When lifting the cleaner out of the water, you must ensure that the
cleaner does not hit the side of the pool wall, otherwise you may dam-
age both the cleaner and the liner.

Before the cleaner clears the surface of the water, it must be held
there for 10 to 15 seconds, so that most of the water can flow out of
the water outlet into the pool. Only then should you put the cleaner on
the edge of the swimming pool.
Clean the filter tray
Fig. 11

Lift the tray handle up

Take out the filter tray

Slide the clip to open the tray

Take the slides off

Clean the tray
Put the filter tray back
Fig.12
Machine have a slide way to lead filter tray back into the cleaner, and
clip the handle in position perfectly.
Hints and tips
Every time the cleaner is taken out of the water, the filter cleaner must
be cleaned.
Make sure the pH value of the water is between 7.0 and 7.2.
Make sure the water temperature is between 10°C and 32°C.
After every clean, the drive train must be thoroughly cleaned to en-
sure the same level of grip on the next clean.
After pressing the “Power Off” button, the “Power On” button cannot
be pressed for 30 seconds.
We recommend keeping the cleaner between 10°C and 32°C in a
shaded, well ventilated place. Avoid direct sunlight at all times.
We recommend attaching the operating unit with a safety rope, to
avoid any risk of the power pack being pulled into the pool.
Before use, please read the instructions relating to trouble-shooting
thoroughly.
Trouble shooting
Guarantee
A guarantee will only be undertaken by the manufacturer with regard
to safety and reliability under the following circumstances:

The floor vacuum cleaner is used in accordance with the guidance
in the instruction manual.

Only original replacement parts were used in any repairs (Parts
liable to wear and tear are not covered by guarantee).
6
▶
Manual right turn
7 Stop sign Manual stop machine
8 mode
●Pool floor mode
●Pool wall mode
●One floor one wall mode
●Three floor one wall mode
9 Auto play or stop
●Auto Play: working as selected
mode
●STOP: stop working automatically
Diagnose
Indicator Meaning Suggestion
1H flash quickly with
buzz
Machine
out of wa-
ter
Put machine
back
into
water or wait
until
ma-
chine restart
automati-
cally
All lights flash quickly
with buzz
Control
box
over
load
Stop ma-
chine
contact after
sale service
person
1H+2H+3H flash quick
with buzz Seal box
leaking
Stop ma-
chine
contact after
sale service
person
ALL+1H flash quick
with buzz Pump over
load
Stop ma-
chine check
the impeller
and pump
WALL+2H quick with
buzz
Walking
motor 1
over load
Stop ma-
chine check
belt
and
transmission
system
FLOOR+3H
flash quick with buzz
Walking
moter 2
over load
Stop ma-
chine check
belt
and
transmission
system
ALL+WALL+1H+2H
flash quick with buzz
Cleaner
present
abnormal-
voltage
Stop ma-
chine
contact after
sale service
person
ALL+WALL+FLOOR
flash quick with buzz
Abnormal
communi-
cation
Check the
cable
between
cleaner and
control box
or
contact
the after
sale service
person
WALL+FLOOR+2H+3H
flash quick with buzz Machine
out of wa-
ter
and
could not
restart
Stop ma-
chine restart
machine
manually af-
ter cleaner
sink
WALL flash quick with
buzz Machine
turned
over Turn over
machine
manually