background image

D3X RS 

D3X RS Operator’s Manual 

19 

3.10. Adjusting the gib clearance 

Every 50 operation hours, or more often, check the gib clearance because it greatly 
influences the quality of drilled holes. The clearance is appropriate if the motor slides 
smoothly and not drops under its own weight. 
 

To remove the excessive clearance, use the 8 mm combination wrench to loosen 

the nuts (

1

, Fig. 11), and then use the 2.5 mm hex wrench to loosen the set screws (

2

). 

Next, rotate the spoke handles to set the motor on such a level to access the gib 
screws through the holes, use the 4 mm hex wrench to loosen these screws (

3

), and 

then tighten (

4

) with a force enough to prevent the gib from being pushed out by the 

springs located inside. 
 

Use the 2.5 hex wrench to tighten the set screws (

5

) to such an extent that the 

motor moves smoothly through the entire stroke and not drops under its own weight. 
Next, use the 4 mm hex wrench to tighten the gib screws: central screw (

6

), adjacent 

screws, and then top and bottom screws. Finally, use the 8 mm combination wrench to 
tighten the nuts (

7

), while countering the set screws using the 2.5 mm hex wrench (

8

). 

Содержание D3X RS



































Отзывы: