SteelBeast PRO 2 PB Series Скачать руководство пользователя | Manualshive

Страница: 9 / 29

background image

PB2

This document is protected by copyrights.

Copying, using, or distributing without permission of JEI Group Ltd is prohibited.

9

21. Do not touch chips or moving parts. Do not let anything catch in moving parts.

22. After each use, remove chips and coolant from the machine. Do not remove

chips with bare hands. Clean the machine with a cotton cloth and no chemical

agents.

23. Maintain the machine and install/remove parts and tool bits only after you unplug

the machine from the air (power) source or remove the battery.

24. Repair only in a service center appointed by the seller.

25. If the machine falls, is wet, or has any damage, stop the work and promptly send

the machine to the service center for check and repair.

26. Do not leave the machine when it operates.

27. If you are not going to use the machine, remove the tool bits from the sockets.

Then, remove the machine from the worksite and keep it in a safe and dry place.

28. If you are not going to use the machine for an extended period, put anti-corrosion

material on the steel parts.

«
...
7
8
9
10
11
...
»

Содержание PRO 2 PB Series






























Отзывы:

Нет отзывов

Похожие инструкции для PRO 2 PB Series

Бренд: CCS Страницы: 24

Бренд: P.A. Страницы: 32

Бренд: RIDGID Страницы: 43

eXtreme Power 650W

Бренд: Cooler Master Страницы: 57

Бренд: Enerpac Страницы: 16

Бренд: Elektro-Automatik Страницы: 4

XTC ARGB Series

Бренд: COUGAR Страницы: 2

MAG-8200 Series

Бренд: Magna-Matic Страницы: 10

Бренд: Ubiquiti Страницы: 28

Бренд: Chicago Pneumatic Страницы: 36

Бренд: joke Страницы: 12

Бренд: Parkside Страницы: 258

Бренд: SATA Страницы: 16

Бренд: Cleco Страницы: 20

GT-86121-1224-W2E

Бренд: W&T Страницы: 14

MOVITRANS THM20C

Бренд: SEW-Eurodrive Страницы: 64

Бренд: Palmgren Страницы: 46

Бренд: KNOVA Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды