4
1
2
1
TIME
TEMP
IM
STOP
3
2
6
5
7
1½“ Hole
located four feet
from the floor
Double-Sided
Adhesive Pad
IMPORTANT:
Run the
Control Cable through
a ¾” conduit.
Coupler
To Steam Generator
Inside Installation:
TSC-250 Control. Locate
away from the direct line
of shower spray and do
NOT locate above
steamhead.
C
US
®
Installation & Operating Instructions
06/11
Pub. No. 271-B
- 1 -
Steambath Control
Models: TSC-250 & TSC-250T
Control Features
1.
Display: The digital read out displays the ambient temperature, set point
and remaining time in minutes. It is also used to display diagnostic error
codes.
2.
Steam Icon: When illuminated the steam cycle is running.
3.
Water Icon: When steam shower is not in use the blue water waves
indicate the InstaMist feature is on. This is also illuminated when the
steam bath cycle is running.
4.
Time / Temp button: Used to program the default timer when the steam
bath is off. Adjustments are made with the Up/Down buttons. The button
will switch between time and temperature when the steam bath is on.
Adjustments to the timer made during a steam bath cycle are temporary.
All temperature adjustments are held in memory for the user of the cycle
that is running.
5.
IM/Stop button: Toggles the InstaMist feature on/off when the steam
bath is off and stops the steam bath cycle when a cycle is started.
InstaMist is a preheat function that keeps the water heated for quick
starts.
6.
User 1 button: Starts the user one cycle and is the up function while in
cycle.
7.
User 2 button: Starts the user two cycle and is the down function while
in cycle.
IMPORTANT: This control must be installed inside the steam room
for proper operation of the system.
Cleaning Instructions: Use a damp cloth and mild soap.
Do NOT use abrasive cleaners which might scratch the
surface or the base of the control.
IMPORTANT: The TSC-250 Control will only function with
the current TSG steam generators.
TSC-250 Digital Temperature Control
Installation Instructions
1.
Pre-Installation - Control Location
a) The TSC-250 Control must be installed inside the steam room. For
convenience the recommended height from the floor is four feet. Provide
a 1½" hole in the wall at this location (see Figure 1).
IMPORTANT: Multi-conductor cable must be installed so that the end will
not be buried inside the wall. The unit will not operate unless the control
is installed.
2.
Electrical Rough-in
a) Remove the multi-conductor cable from the control packing box. Carefully
route the multi-conductor control cable from the steam generator to the
TSC-250 located inside the steamroom (see Figure 1). Route
multi-conductor cable through a ¾" conduit to protect the cable from
damage and to facilitate replacement if necessary.
3.
Control and Cable Installation
a)
Locate the previously installed cable and black plastic strain relief clamp
which is in the control packing box. Locate the knockout on the steam
generator for the control cable (see Figure 3).
b) Place strain relief around cable about seven inches from the end and
insert into the hole. Remove the protective covering labeled “Remove
Before Installation” from the modular jack found on the PC board.
c) Remove the protective cap from the multi-conductor cable plug. Connect
the cable to the modular jack.
d) Close and secure generator cover.
e) Locate Telco Jack at female coupler, on back of the TSC-250 control.
Remove the protective covering labeled “Remove Before Installation”.
Remove protective cap from cable and plug into jack. Check that the
orientation of the plug properly aligns with the jack. A snap will
indicate the plug is installed correctly (see Figure 3).
WARNING: Test the control for operation before continuing on
to the next step.
f) Peel adhesive liner from back of the control. Apply the control
to the wall. Press firmly and hold for a few seconds.
g) After the control is in place, apply silicone (supplied) around
the control to form a watertight seal (see Figure 2).
Figure 1
WARNING:
Elderly persons, pregnant women, or those suffering from heart disease, high blood pressure, diabetes, or
who are otherwise not in good health, do not use this device unless directed to do so by a physician. Also, do not use
steambath while under the influence of alcohol. For additional Important Safety Information, please see a separate
instruction sheet Pub. No. 199.
!
®
